Home › Suspension › REAR SUSPENSION › REAR COIL SPRING

REAR COIL SPRING > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL HOLLOW SPRING SUB-ASSEMBLY
  1. Install the hollow spring to the frame.



2. INSTALL REAR COIL SPRING LH


    D028471
  1. Install the rear coil spring to the rear axle housing.

    HINT:
    Before installing the coil spring, check that the coil spring end is in the correct position. If not, reinstall the coil spring.



3. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH
  1. Temporarily install the lower side of the shock absorber with the bolt.



4. INSTALL REAR STABILIZER LOWER BRACKET (w/ KDSS)


    F047862
  1. Support the rear stabilizer bar with a jack.

    NOTICE:
    Place a wooden block between the jack and rear stabilizer bar to prevent damage.



    C214768E01
  1. Install the rear stabilizer bar and 2 rear stabilizer lower brackets with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

    Text in Illustration 
    *1
    Rear Stabilizer Control Cylinder
    *2
    Rear Stabilizer Link

    1. Check that the protrusions on the rear stabilizer bush are positioned within 180° of the rear stabilizer control cylinder and rear stabilizer link.



5. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



6. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
  1. Tighten the bolt.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }



7. CONNECT REAR FLEXIBLE HOSE
  1. Connect the rear flexible hose to the connecting point with each brake tube, and then install 2 new clips.

  1. Using a union nut wrench, connect each brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.
    3. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the rear flexible hose to the connecting point with each brake tube, and then install 2 new clips.

  1. Using a union nut wrench, connect each brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.
    3. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



8. FILL RESERVOIR WITH BRAKE FLUID


    C208936
  1. Turn the engine switch off and fully depress the brake pedal 40 times or more to release the pressure in the accumulator.

    HINT:
    When the pressure in the accumulator is released, the pedal stroke will lengthen.

  1. Adjust the fluid level so that it is at the MAX line.

    HINT:
    When the engine switch is turned on (IG), brake fluid is sent to the accumulator and the fluid level decreases by approximately 10 mm (0.394 in.) from the MAX line.

    Brake fluid:
    SAE J1703 or FMVSS NO. 116 DOT 3



9. BLEED BRAKE LINE
  1. Turn the engine switch on (IG).

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the engine switch off (IG).

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level .



10. CHECK FLUID LEVEL IN RESERVOIR


    C208936
  1. Turn the engine switch off and fully depress the brake pedal 40 times or more to release the pressure in the accumulator.

    HINT:
    When the pressure in the accumulator is released, the pedal stroke will lengthen.

  1. Adjust the fluid level so that it is at the MAX line.

    HINT:
    When the engine switch is turned on (IG), brake fluid is sent to the accumulator and the fluid level decreases by approximately 10 mm (0.394 in.) from the MAX line.

    Brake fluid:
    SAE J1703 or FMVSS NO. 116 DOT 3



11. CHECK FOR BRAKE FLUID LEAK


12. INSTALL REAR WHEEL

Torque:
112 N*m{ 1142 kgf*cm , 83 ft.*lbf }