Home › Suspension › SUSPENSION CONTROL › CENTER CONTROL ABSORBER (w/ REAS)

CENTER CONTROL ABSORBER (w/ REAS) > INSTALLATION

for Preparation Click here



1. INSTALL CENTER CONTROL ABSORBER BRACKET LH
  1. Install the center control absorber bracket with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



2. INSTALL CENTER CONTROL ABSORBER BRACKET RH

HINT:
Use the same procedure described for the LH side.



3. INSTALL CENTER CONTROL ABSORBER ASSEMBLY LH


    C212830
  1. Install the center control absorber assembly with the 3 nuts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    C212829
  1. Connect the tube to the 2 clamps.



    C212827
  1. Install the bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



  1. While using a wrench to hold the bracket, connect the joint.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


    HINT:
    C212836E01
    For the joint that connects supplied parts, tighten the joint while checking the gap spacing shown in the illustration.

    Standard clearance:
    1 mm (0.0394 in.)



4. INSTALL CENTER CONTROL ABSORBER ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



5. INSTALL NO. 1 CENTER CONTROL ABSORBER TUBE LH


    C216451
  1. Install a new No. 1 center control absorber tube with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    C212828
  1. While using a wrench to hold the center control absorber assembly, connect the joint.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


    HINT:
    C212836E01
    For the joint that connects supplied tubes, tighten the joint while checking the gap spacing shown in the illustration.

    Standard clearance:
    1 mm (0.0394 in.)

  1. Pass the center control absorber tube between the body and frame.



    C212835
  1. Attach the 2 clamps.



    C216452
  1. While using a wrench to hold the bracket, connect the joint.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


    HINT:
    C212836E01
    For the joint that connects supplied tubes, tighten the joint while checking the gap spacing shown in the illustration.

    Standard clearance:
    1 mm (0.0394 in.)



    C214836
  1. While using a wrench to hold the bracket, connect the joint.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


    HINT:
    C212836E01
    For the joint that connects the supplied tubes, tighten the joint while checking the gap spacing shown in the illustration.

    Standard clearance:
    1 mm (0.0394 in.)



6. INSTALL NO. 1 CENTER CONTROL ABSORBER TUBE RH

HINT:
Use the same procedure described for the LH side.



7. INSTALL TUBE PROTECTOR LH


    C214834
  1. Install the tube protector LH with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



8. INSTALL TUBE PROTECTOR RH

HINT:
Use the same procedure described for the LH side.



9. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1142 kgf*cm , 83 ft.*lbf }



10. INSTALL REAR WHEEL

Torque:
112 N*m{ 1142 kgf*cm , 83 ft.*lbf }



11. INSPECT FOR FLUID LEAK


  1. Check the tube connections and parts shown in the illustration for fluid leakage.


    C214864



    C216449E01