Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

DTC    C2171/71    Transmitter ID not Registered

for Preparation Click here


DESCRIPTION

The ID of each tire pressure warning valve and transmitter is registered to the tire pressure warning ECU.
When the ECU detects that a transmitter ID code is not registered in the ECU, this DTC is stored.

DTC Code
Detection Condition
Trouble Area
C2171/71
A transmitter ID code is not registered (when an ID code is unregistered for 3 minutes or more).
Tire pressure warning ECU

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using the Techstream and note them down before removal.
  2. It is necessary to perform registration of the transmitter IDs into the tire pressure warning ECU after the ECU and/or the tire pressure warning valve and transmitter has been replaced (Click here).

1.CONFIRM REGISTRATION CONDITION (REGISTERED ID CODES)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Registered ID1 Code
    Registered ID1 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID1 displayed
    *: Displayed only when the ID No. is not registered.
    Registered ID2 Code
    Registered ID2 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID2 displayed
    *: Displayed only when the ID No. is not registered.
    Registered ID3 Code
    Registered ID3 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID3 displayed
    *: Displayed only when the ID No. is not registered.
    Registered ID4 Code
    Registered ID4 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID4 displayed
    *: Displayed only when the ID No. is not registered.
    Result 
    Result
    Proceed to
    1 or more transmitter ID codes are not registered
    A
    All transmitter ID codes are registered
    B



B
Go to step 3
A


2.PERFORM REGISTRATION (TRANSMITTER ID)
  1. Register the transmitter IDs for all the wheels (Click here).


NEXT


3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    1. *: It may take approximately 2 or 3 minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.


    Result 
    Result
    Proceed to
    All tire pressure readings are equal to specified values
    A
    Tire pressure values are not displayed
    B



B
REPLACE TIRE PRESSURE WARNING ECU (Click here)
A

END