Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP

VANE PUMP > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP ASSEMBLY
  1. Install the vane pump with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the wire harness bracket with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



2. CONNECT NO. 1 PRESSURE FEED TUBE
  1. Install a new gasket to the pressure feed tube.

  1. Connect the pressure feed tube and install the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



3. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE
  1. Connect the No. 1 oil reservoir to pump hose to the vane pump assembly with the clip.



4. CONNECT POWER STEERING OIL PRESSURE SWITCH CONNECTOR
  1. Connect the 2 connectors.



5. INSTALL FAN AND GENERATOR V BELT


    A225650E01
  1. Set the V belt onto every part.
    Text in Illustration 
    *1
    Vane Pump
    *2
    Water Pump
    *3
    No. 2 Idler
    *4
    Generator
    *5
    Cooler Compressor
    *6
    No. 1 Idler
    *7
    Crankshaft
    *8
    V-ribbed Belt Tensioner

  1. While turning the belt tensioner counterclockwise, remove the pin.

    NOTICE:
    Make sure that the V belt is properly installed to each pulley.

  1. Check that the belt fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



6. INSTALL AIR CLEANER CASE
  1. Install the air cleaner case sub-assembly with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the air cleaner filter element sub-assembly.



7. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


8. INSTALL AIR CLEANER CAP AND HOSE


    A223697E01
  1. Install the air cleaner cap and hose.
    Text in Illustration 
    *a
    Upper
    *b
    Front
    *c
    RH
    *d
    Align cutout portion of hose with protrusion of throttle
    *e
    Paint Mark

    1. Install the air cleaner cap and hose with the bolt and fasten the 4 hook clamps.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    2. Tighten the clamp.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Attach the 4 clamps and connect the ventilation hose, vacuum hose and mass air flow meter connector.

      HINT:
      The direction of the hose clamp is indicated in the illustration.



9. INSTALL V-BANK COVER SUB-ASSEMBLY


    A229926E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



10. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal RH with the 4 clips.



11. INSTALL FRONT WHEEL RH


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


13. ADD POWER STEERING FLUID


14. BLEED AIR FROM POWER STEERING FLUID
  1. Bleed air from the power steering fluid (Click here).



15. INSPECT FOR POWER STEERING FLUID LEAK