Home › General › SPECIFICATIONS › 1GR-FE ENGINE CONTROL

1GR-FE ENGINE CONTROL > SERVICE DATA



Camshaft Timing Oil Control Valve:

Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω


Crankshaft Position Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω


Engine Coolant Temperature Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ


Throttle Body:

Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω


Knock Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ


Accelerator Pedal:

Accelerator Pedal Operation
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 5.3 V


Air Fuel Ratio Sensor (for Bank 1):

Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-)
Always
10 kΩ or higher


Air Fuel Ratio Sensor (for Bank 2):

Tester Connection
Condition
Specified Condition
1 (HA2A) - 2 (+B)
20°C (68°F)
1.6 to 3.2 Ω
1 (HA2A) - 4 (A2A-)
Always
10 kΩ or higher


Heated Oxygen Sensor (for Bank 1):

Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT1B) - 4 (E2)
Always
10 kΩ or higher


Heated Oxygen Sensor (for Bank 2):

Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT2B) - 4 (E2)
Always
10 kΩ or higher


No. 1 Integration Relay (IG2):

Tester Connection
Condition
Specified Condition
IG2 fuse
Always
Below 1 Ω
1E-1 - 1C-4
Battery voltage not applied to terminals 1C- 1 and 1C-3
10 kΩ or higher
Battery voltage applied to terminals 1C-1 and 1C-3
Below 1 Ω


No. 1 Integration Relay (EFI):

Tester Connection
Condition
Specified Condition
EFI fuse
Always
Below 1 Ω
1E-1 - 1D-4
Battery voltage not applied to terminals 1D- 2 and 1D-3
10 kΩ or higher
Battery voltage applied to terminals 1D-2 and 1D-3
Below 1 Ω


No. 1 Integration Relay (A/F):

Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1E-1 - 1D-8
Battery voltage not applied to terminals 1D- 4 and 1D-7
10 kΩ or higher
Battery voltage applied to terminals 1D-4 and 1D-7
Below 1 Ω


Air Pump Heater Relay:

Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Air Injection VSV Relay (AI-VSV):

Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Main Body ECU (Driver Side Junction Block) for ACC Relay:

Tester Connection
Condition
Specified Condition
2B-17 - 2E-1
Battery voltage not applied to terminals 2C- 48 and 2B-4
10 kΩ or higher
Battery voltage applied to terminals 2C-48 and 2B-4
Below 1 Ω


Main Body ECU (Driver Side Junction Block) for IG1 No. 2 Relay:

Tester Connection
Condition
Specified Condition
2C-31 - 2E-1
Battery voltage not applied to terminals 2C- 52 and 2B-4
10 kΩ or higher
Battery voltage applied to terminals 2C-52 and 2B-4
Below 1 Ω


Spark Plug:

Recommended spark plug
Correct electrode gap for new spark plug
Maximum electrode gap for used spark plug
Standard insulation resistance
SK20HR11
Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.)
1.3 mm (0.0512 in.)
10 MΩ or higher