Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus:

    1. Body Electrical / Air Conditioner / Data List.
    2. Powertrain / Engine and ECT / Data List.

  5. According to the display on the Techstream, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Cooler thermistor (room temperature sensor) /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual room temperature for front seat displayed
    Open in the circuit: -6.5°C (20.3°F).
    Short in the circuit: 57.25°C (135.05°F).
    Ambient Temp Sensor
    Cooler thermistor (ambient temperature sensor) /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    Open in the circuit: -23.3°C (-9.94°F).
    Short in the circuit: 65.95°C (150.71°F).
    Adjusted Ambient Temp
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    Adjusted ambient temperature displayed
    -
    Evaporator Fin Thermistor
    No. 1 cooler thermistor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature displayed
    Open in the circuit: -29.7°C (-21.46°F).
    Short in the circuit: 59.55°C (139.19°F).
    Evaporator Target Temp
    Target evaporator temperature /
    Min.: -327.68°C (-557.82°F)
    Max.: 327.67°C (621.81°F)
    Target evaporator temperature displayed
    -
    Solar Sensor (D Side)
    Automatic light control sensor (solar sensor) / Min.: 0, Max.: 255
    Driver side solar sensor voltage increases as brightness increases
    Open in the circuit: 0.
    Short in the circuit: 255.
    Solar Sensor (P Side)
    Automatic light control sensor (solar sensor) / Min.: 0, Max.: 255
    Passenger side solar sensor voltage increases as brightness increases
    Open in the circuit: 0.
    Short in the circuit: 255.
    Engine Coolant Temp
    Engine coolant temperature /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature displayed
    -
    Set Temperature (D Side)
    Driver side set temperature /
    MAX COLD: 17.5°C (63.5°F)
    MAX HOT: 32.5°C (90.5°F)
    Driver side set temperature displayed
    -
    Set Temperature (P Side)
    Passenger side set temperature /
    MAX COLD: 17.5°C (63.5°F)
    MAX HOT: 32.5°C (90.5°F)
    Passenger side set temperature displayed
    -
    Blower Motor Speed Level
    Blower with fan motor sub-assembly speed level / Min.: 0, Max.: 31
    Increases in range from 0 to 31 as blower with fan motor sub-assembly speed increases
    -
    Air Mix Servo Targ Pulse (D)
    Damper servo sub-assembly (driver side air mix damper servo) target pulse / Min.: 0, Max.: 255
    107 (pulse): MAX COOL
    26 (pulse): MAX HOT
    -
    Air Mix Servo Actual Pulse (D)
    Damper servo sub-assembly (driver side air mix damper servo) actual pulse / Min.: 0, Max.: 255
    107 (pulse): MAX COOL
    26 (pulse): MAX HOT
    -
    Air Mix Servo Targ Pulse (P)
    Damper servo sub-assembly (front passenger side air mix damper servo) target pulse / Min.: 0, Max.: 255
    112 or 127 (pulse): MAX COOL
    21 or 31 (pulse): MAX HOT
    -
    Air Mix Servo Actual Pulse (P)
    Damper servo sub-assembly (front passenger side air mix damper servo) actual pulse / Min.: 0, Max.: 255
    112 or 127 (pulse): MAX COOL
    21 or 31 (pulse): MAX HOT
    -
    Air Outlet Servo Pulse (D)
    Damper servo sub-assembly (mode damper servo) target pulse / Min.: 0, Max.: 255
    15 (pulse): FACE 1
    15 (pulse): FACE 2
    41 (pulse): B/L
    65 or 73 (pulse): FOOT
    83 or 95 (pulse): F/D
    113 (pulse): DEF
    -
    Air Outlet Servo Actu Pulse (D)
    Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255
    15 (pulse): FACE 1
    15 (pulse): FACE 2
    41 (pulse): B/L
    65 or 73 (pulse): FOOT
    83 or 95 (pulse): F/D
    113 (pulse): DEF
    -
    Air Inlet Damper Targ Pulse
    Recirculation damper servo sub-assembly target pulse / Min.: 0, Max.: 255
    7 (pulse): Recirculation
    28 (pulse): Fresh
    -
    Air Inlet Damper Actual Pulse
    Recirculation damper servo sub-assembly actual pulse / Min.: 0, Max.: 255
    7 (pulse): Recirculation
    28 (pulse): Fresh
    -
    Electric Heater Active Level*
    Number of electric heaters operating / Min.: 0, Max.: 3
    -
    -
    Shift Set Temperature
    Set temperature shift / 2C incr, 1C incr, Normal, 1C decr or 2C decr
    Customized value displayed
    -
    Compressor Mode
    Compressor mode / Auto or Manual
    Customized setting displayed
    -
    Add Foot Air in FACE Mode
    Add foot air in face mode / ON or OFF
    Customized setting displayed
    -
    Foot/DEF Auto Mode
    Foot/Def auto mode / ON or OFF
    Customized setting displayed
    -
    Foot/DEF Auto Blow Up
    Foot/Def auto blower level function / ON or OFF
    Customized setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0, Max.: 255
    Number of DTCs stored
    -

    1. *: w/ PTC Heater

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    A/C signal / ON or OFF
    ON: A/C switch on
    OFF: A/C switch off
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  5. According to the display on the Techstream, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower with fan motor sub-assembly
    Min.: 0, Max.: 31
    -
    Magnetic Clutch Relay
    Magnet clutch relay operation
    ON or OFF
    -
    Defogger Relay (Rear)
    Rear window defogger relay operation
    ON or OFF
    -
    Heater Active Level*
    Heater level
    Min.: 0, Max.: 3
    -
    Air Mix Servo Targ Pulse (D)
    Damper servo sub-assembly (driver side air mix damper servo) target pulse
    Min.: 0, Max.: 255
    -
    Air Mix Servo Targ Pulse (P)
    Damper servo sub-assembly (front passenger side air mix damper servo) target pulse
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse (D)
    Damper servo sub-assembly (mode damper servo) pulse
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    Recirculation damper servo sub-assembly target pulse
    Min.: 0, Max.: 255
    -

    1. *: w/ PTC Heater