ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Engine switch on (IG) signal / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| #Codes | Number of trouble codes / Min: 0, Max: 255 | Number of stored DTCs displayed | - |
| Immobiliser | Engine immobiliser system status / Set or Unset | Set: Key not in cabin Unset: Key in cabin | - |
| Master Key | Master key code signal / Match or No Match | Match: Master key code sent No Match: Unmatched master key code sent | - |
| Sub Key | Sub-key (master key) code signal / Match or No Match | Match: Sub-key (master key) code sent No Match: Unmatched sub-key (master key) code sent | - |
| BCC Malfunction | Transponder chip signal / OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Abnormal Status | Transponder chip data / OK or NG | OK: Data OK NG: Data error | - |
| Different Encrypt Code | Transponder chip signal / OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Different Serial Number | Transponder chip signal / OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Frame Error | Transponder chip signal / OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Response | Transponder chip signal / OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Wireless Starter Com ID | Wireless starter communication ID / No Regd or Regd | No Regd: Wireless starter communication ID not registered Regd: Wireless starter communication ID registered | - |
| Wireless C Code | Wireless C code / No Regd or Regd | No Regd: Wireless C code not registered Regd: Wireless C code registered | - |
| ID-BOX Sleep Condition | ID code box condition / Yes or No | Yes: ID code box in sleep condition No: ID code box not in sleep condition | - |
| ID-BOX Start Condition | ID code box condition / Yes or No | Yes: ID code box sends wake up signal No: ID code box does not send wake up signal | - |
| Engine Start Request | ID code box start request condition / OK or NG | OK: Start request condition signal received (past) NG: Start request condition signal not received (past) | - |
| S Code Check | S code verification result / OK or NG | OK: Verification confirmed NG: Verification not confirmed | - |
| L Code Check | L code verification result / OK or NG | OK: Verification confirmed NG: Verification not confirmed | - |
| Unlock Request Receive | Steering unlock command reception status / OK or NG | OK: Steering unlock request received NG: Steering unlock request not received | - |
| Lock Request Receive | Steering lock command reception status / OK or NG | OK: Steering lock request received NG: Steering lock request not received | - |
| S Code Check (Past) | S code verification result (past) / OK or NG | OK: Verification confirmed (past) NG: Verification not confirmed (past) | - |
| L Code Check (Past) | L code verification result (past) / OK or NG | OK: Verification confirmed (past) NG: Verification not confirmed (past) | - |
| EFI Code Receive | SFI code received (when DTC stored) / OK or NG | OK: SFI code received NG: SFI code not received | - |
| EFI communication | SFI communication / OK or NG | OK: SFI communication normal NG: SFI communication abnormal | - |
| PERFORM ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Immobiliser Indicator | Security indicator light | ON/OFF | The test is possible when the following conditions are met:
|