Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



1. REMOVE ENGINE UNDER COVER SEAL
  1. Remove the 2 bolts and engine under cover seal.



2. REMOVE COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)


    B353485
  1. Remove the 4 clips and cool air intake duct.



3. DISCONNECT FRONT LOWER BUMPER COVER


    A225444
  1. Remove the 2 bolts and clip, and disconnect the front bumper lower cover.



4. DISCONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    A224795
  1. Remove the 4 bolts and open the No. 1 engine under cover sub-assembly as shown in the illustration.



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. REMOVE OIL FILTER ELEMENT


    A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A222100
  1. Remove the oil filter drain plug.



    A222101E01
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    Valve
    *3
    Pipe
    *4
    O-ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A222102
  1. Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.



    A222103E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.



    A153538E03
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.



7. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, the threads and O-ring groove.



    A268595E01
  1. Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.
    Text in Illustration 
    *1
    O-ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element on the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    NOTICE:
    Do not pinch the O-ring for the cap.



    A292826E01
  1. Using SST, tighten the oil filter cap.

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *3
    Oil Filter Bracket
    *4
    Oil Filter Bracket Clip
    *a
    No gap

    NOTICE:
    1. After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.
    2. When tightening the oil filter cap, do not remove the oil filter bracket clip.



    A222105E01
  1. Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



8. ADD ENGINE OIL


  1. Add fresh engine oil.

    NOTICE:
    A308107
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

    If engine oil is on the location indicated by the arrow, replace the belt tensioner.

    Standard Engine Oil:

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    0W-20


    Standard Oil Capacity:

    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)



9. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    Engine oil is always being consumed when driving the vehicle.
    Generally, engine oil consumed at a rate of 1 liter every 3000 km, or 1 US qts. every 2000 miles.
    In the following situations, oil consumption may increase and it may be necessary to add oil between maintenances.
    1. The engine is new.
    2. The oil quality is poor or the viscosity is inappropriate.
    3. The engine speed or load is high, the vehicle is towing something or the vehicle is being accelerated and decelerated frequently.
    4. The engine is idled for a very long time or the vehicle is frequently driven in traffic.



10. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



11. CONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    A225431
  1. Close the No. 1 engine under cover sub-assembly with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



12. CONNECT FRONT LOWER BUMPER COVER
  1. Connect the front lower bumper cover with the 2 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



13. INSTALL COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)
  1. Install the cool air intake duct with the 4 clips.



14. INSTALL ENGINE UNDER COVER SEAL
  1. Install the engine under cover seal with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }