SMART KEY SYSTEM (for Entry Function) > OPERATION CHECK |
| SMART KEY SYSTEM OPERATION INSPECTION |
Check the entry unlock function.
Use the wireless lock operation to lock the doors. With the key in your possession, touch a door outside handle (unlock sensor) and check that the door unlocks.
Check the entry unlock operation detection area.
![]() |
Step 1: Hold the key at the same height as the door outside handle (approximately 0.8 m [2.62 ft.]). Pay attention to the direction of the key in the illustration.
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
Step 2: Check that when the key is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the vehicle, the system enters unlock standby mode.
![]() |
Step 3: After the system enters unlock standby mode, touch the unlock sensor on the outside handle within 3 seconds. Check that the door unlocks.
| *1 | Unlock Sensor |
Step 4: Repeat step 2 and step 3 for the other front door.
![]() |
Step 5: Inspect the unlock sensor response sensitivity. Wear protective gloves, set the system to unlock standby mode, and check that touching the inner side of the outside handle (the highlighted area in the illustration) with your finger causes the door to unlock.
| *1 | Unlock Sensor |
Step 6: Repeat step 5 for the other front door.
Check the entry lock function.
![]() |
Step 1: Close all the doors of the vehicle. With the key outside the vehicle, check that touching the lock sensor locks the doors.
| *1 | Lock Sensor |
![]() |
| *a | Approximately 0.3 m (0.984 ft.) |
Step 2: Repeat step 1 for the other front door.
Check the entry back door unlock function.
Lock all the doors and the back door. With the key in your possession, check that pressing the unlock switch on the back door control switch or the back door opener switch unlocks all the doors and the back door.
![]() |
Inspect the detection area of the entry back door unlock operation. Hold the key at the same height as the back door control switch (approximately 0.8 m [2.62 ft.]) Pay attention to the direction of the key shown in the illustration. Check that the when the key is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the vehicle, pressing the unlock switch on the back door control switch or the back door opener switch unlocks all the doors and the back door.
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
Check the entry back door lock function.
Step 1: Close all of the vehicle doors. With the key in your possession outside of the vehicle, check that pressing the back door lock switch locks all the doors.
![]() |
| *a | Approximately 0.3 m (0.984 ft.) |
Check the entry ignition function.
When the engine control system is off: With the key in your possession and the brake pedal depressed, check that pressing the engine switch releases the steering wheel lock and starts the engine control system.
When the engine control system is running: With the key in your possession, check that pressing the engine switch stops the engine control system and activates the steering wheel lock.
![]() |
Inspect the detection area of the entry ignition operation (front seat). Pay attention to the direction of the key in the illustration. When the key is in either of the 2 locations in the illustration, check that the engine control system can be started. Then repeat the check with the key in the other location.
| *a | Inspection Point |
![]() |
Inspect the detection area of the entry ignition operation (rear seat). Pay attention to the direction of the key in the illustration. When the key is in either of the 2 locations in the illustration, check that the engine control system can be started. Then repeat the check with the key in the other location.
| *a | Inspection Point |
![]() |
Inspect the detection area of the entry ignition operation (luggage room). Pay attention to the direction of the key in the illustration. When the key is in either of the 2 locations in the illustration, check that the engine control system can be started. Then repeat the check with the key in the other location.
| *A | w/ Rear No. 2 Seat Assembly |
| *B | w/o Rear No. 2 Seat Assembly |
| *a | Inspection Point |
Check the key lock-in prevention function.
Place the key in the vehicle, close the doors, perform the entry lock operation (touch the lock sensor on the door outside handle) and check that the buzzer sounds for a specified period of time and all the doors are unlocked.
Open the back door, place the key in the vehicle with the other doors closed and locked, close the back door and check that the buzzer sounds for a specified period of time and the back door does not lock when the lock switch is pressed.
Check the key cancel function.
While the engine switch is on (IG), check that the back door unlock switch is the only switch in the smart key system that can be operated.
While the key cancel function (smart key system cancel function) is on, check that all functions of the smart key system cannot be operated.
Check the answer-back function (hazard warning light flashing).
| Entry Operation | Hazard Warning Light |
| Entry Door Lock | Flashes once |
| Entry Door Unlock | Flashes twice |
| Entry Back Door Lock | Flashes once |
| Entry Back Door Unlock | Flashes twice |
Check that the key reminder warning buzzer sounds.
With the key inside the vehicle, close the driver side door. Then turn the engine switch off or on (ACC).
Open the driver side door and check that the buzzer sounds intermittently.
Check that the key reminder warning buzzer stops.
When the buzzer is sounding, check that the buzzer stops sounding if either of the following is performed: