Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B167608E07

  1. Disconnect the F17 amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F17-7 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F17 amplifier connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F17-1 (VC5) - F17-7 (AGND)
    B - L
    Power supply
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    F17-4 (CODE) - F17-7 (AGND)
    LG - L
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 1)
    F17-5 (TXCT) - F17-7 (AGND)
    V - L
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 2)
    If the result is not as specified, the amplifier may have a malfunction.



  5. B069240E27
  6. Inspect using an oscilloscope.

    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F17-4 (CODE) - F17-7 (AGND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    2. B069239E24
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F17-5 (TXCT) - F17-7 (AGND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY

B121962E17

  1. Disconnect the F34 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F34-16 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F34-1 (+B) - F34-16 (GND)
    P - W-B
    Battery
    Always
    11 to 14 V
    F34-2 (IG) - F34-16 (GND)
    W - W-B
    Ignition switch
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    F34-3 (KSW) - F34-16 (GND)
    B - W-B
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F34 ECU connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F34-14 (VC5) - F34-16 (GND)
    B - W-B
    Power source
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    F34-7 (CTY) - F34-16 (GND)
    R - W-B
    Front door courtesy light switch (for Driver Side)
    Driver door closed
    10 kΩ or higher
    Driver door open
    Below 1 Ω
    F34-4 (TXCT) - F34-16 (GND)
    V - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 1)
    F34-15 (CODE) - F34-16 (GND)
    LG - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 2)
    F34-13 (EFIO) - F34-16 (GND)
    W - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 3)
    F34-12 (EFII) - F34-16 (GND)
    SB - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation (See waveform 4)
    F34-8 (IND) - F34-16 (GND)
    L - W-B
    Security indicator light signal
    Immobiliser set
    Alternating between 11 to 14 V and below 1 V
    Immobiliser unset
    Below 1 V
    F34-9 (D) - F34-16 (GND)
    G - W-B
    Diagnosis tester communication
    Always
    Pulse generation
    F34-5 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, the ECU may have a malfunction.



  5. B069239E25
  6. Inspect using an oscilloscope.

    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F34-4 (TXCT) - F34-16 (GND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    2. B069240E28
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F34-15 (CODE) - F34-16 (GND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    4. B237527E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F34-13 (EFIO) - F34-16 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON



    6. B229710E01
    7. Waveform 4 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F34-12 (EFII) - F34-16 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected


CHECK ECM

A225776E02

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F50-20 (IMO) - Body ground
    SB - Body ground
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation
    (See waveform 1)
    F50-14 (IMI) - Body ground
    W - Body ground
    Transponder key ECU input signal
    Ignition switch off → ON
    Below 1 V → Pulse generation
    (See waveform 2)
    If the result is not as specified, the ECM may have a malfunction.



  2. Inspect using an oscilloscope.



      B229710E01
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F50-20 (IMO) - Body ground
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected



    2. B237527E01
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F50-14 (IMI) - Body ground
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON