Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSTALLATION

for Preparation Click here



1. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH
  1. Install the front No. 1 engine mounting bracket RH with the 4 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Install the front No. 1 engine mounting bracket LH with the 3 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



3. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    A223631E01
  1. Install a new O-ring to the engine oil level dipstick guide.
    Text in Illustration 
    *1
    New O-Ring

  1. Apply a light coat of engine oil to the O-ring.

  1. Push the engine oil level dipstick guide end into the guide hole.

  1. Install the engine oil level dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the engine oil level dipstick.



4. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A226495E01
  1. Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.

    Standard Bolt:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

  1. Tighten bolts 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. for Separate Type:
    Install the 2 idler pulley cover plates, 2 No. 2 idler pulley sub-assemblies and 2 No. 2 idler pulley cover plates with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. for Integrated Type:
    Install the 2 No. 2 idler pulley sub-assemblies with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



6. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A076438E01
  1. Install the No. 1 idler pulley sub-assembly with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    "DOUBLE" is marked on the No. 1 idler pulley sub-assembly to distinguish it from the No. 2 idler pulley sub-assembly.



7. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY


    A223698E01
  1. Install the water by-pass pipe sub-assembly with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 2 hoses.
    Text in Illustration 
    *a
    Upward
    *b
    Rearward

    HINT:
    The direction of the hose clamp is indicated in the illustration.



8. INSTALL INTAKE MANIFOLD


    A221467
  1. Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Be careful of the installation direction.

  1. Set the intake manifold on the cylinder heads.



    C289995
  1. Install and uniformly tighten the 6 bolts and 4 nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    HINT:
    Tighten the inner installation bolts of the intake manifold before tightening the outer bolts.



9. INSTALL FUEL INJECTOR ASSEMBLY


    A223045E01
  1. Install a new insulator to each fuel injector.
    Text in Illustration 
    *1
    New Insulator
    *2
    New O-Ring

  1. Apply a light coat of spindle oil or gasoline to new O-rings and install one to each fuel injector.



    A223046E01
  1. Install the 6 injectors.

    1. While turning each fuel injector left and right, install it to the fuel delivery pipe.
      Text in Illustration 
      *1
      Connector
      V100135
      Outward
      V100136
      Turn
      V100137
      Push

    2. Position the fuel injectors with the connectors facing outward.



10. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
  1. Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.

  1. Temporarily install the 4 bolts, which are used to hold the fuel delivery pipe in place, to the intake manifold.



    A223047E01
  1. Check that the fuel injectors rotate smoothly.
    Text in Illustration 
    *1
    Turn
    If the fuel injectors do not rotate smoothly, replace the O-ring of any injector that does not rotate smoothly.

  1. Position the fuel injectors with the connectors facing outward.

  1. Tighten the 6 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 6 fuel injector connectors.



11. INSTALL FUEL PIPE SUB-ASSEMBLY
  1. Install the fuel pipe with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 fuel pipes (Click here).



12. INSTALL REAR CYLINDER HEAD COVER
  1. Temporarily install the cover with the 3 bolts.



    A224695E01
  1. Tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



13. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



14. INSTALL NO. 2 EMISSION CONTROL VALVE SET
  1. Install the No. 2 emission control valve set with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



15. INSTALL NO. 1 EMISSION CONTROL VALVE SET
  1. Install the No. 1 emission control valve set with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



16. INSTALL HEATER WATER HOSE ASSEMBLY
  1. Install the heater water hose assembly and connect the 2 hoses.



17. INSTALL ENGINE WIRE