Home › Drivetrain · VF4BM TRANSFER / 4WD / AWD › TRANSFER SYSTEM

TRANSFER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK FOUR WHEEL DRIVE CONTROL ECU

C159461E10

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F47-1 (HL1) - F46-4 (GND)
    GR - W-B
    High-low transfer shift actuator limit switch
    Ignition switch ON
    Transfer position switch H4F or H4L
    10.5 to 14 V
    Ignition switch ON
    Transfer position switch L4L
    Below 1.5 V
    F47-2 (HL2) - F46-4 (GND)
    LG - W-B
    High-low transfer shift actuator limit switch
    Ignition switch ON
    Transfer position switch H4F or H4L
    Below 1.5 V
    Ignition switch ON
    Transfer position switch L4L
    10.5 to 14 V
    F47-6 (TL1) - F46-4 (GND)
    W-B - W-B
    Transfer operating switch mode selection signal
    Always
    Below 1 Ω
    F47-7 (TL2) - F46-4 (GND)
    L - W-B
    Multi mode transfer shift actuator limit switch
    Ignition switch ON
    Transfer position switch H4L or L4L
    Below 1.5 V
    Ignition switch ON
    Transfer position switch H4F
    10.5 to 14 V
    F47-8 (TL3) - F46-4 (GND)
    R - W-B
    Multi mode transfer shift actuator limit switch
    Ignition switch ON
    Transfer position switch H4L or L4L
    10.5 to 14 V
    Ignition switch ON
    Transfer position switch H4F
    Below 1.5 V
    F47-11 (2-4) - F46-4 (GND)
    W - W-B
    Transfer position switch
    Ignition switch ON
    Transfer position switch H4F or H4L
    Below 1.5 V
    Ignition switch ON
    Transfer position switch L4L
    10.5 to 14 V
    F47-13 (LO) - F46-4 (GND)
    B - W-B
    Transfer position switch
    Ignition switch ON
    Transfer position switch H4F
    10.5 to 14 V
    Ignition switch ON
    Transfer position switch H4L or L4L
    Below 1.5 V
    F47-14 (P1) - F46-4 (GND)
    W - W-B
    Multi mode transfer shift actuator
    Center differential lock position detection switch
    Ignition switch ON
    Transfer position switch H4F
    9.5 to 14 V
    Ignition switch ON
    Transfer position switch H4L or L4L
    Below 1.5 V
    F47-19 (CANH) - F46-4 (GND)
    G - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation (See waveform 1)
    F47-20 (CANL) - F46-4 (GND)
    W - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation (See waveform 2)
    F47-21 (L4) - F46-4 (GND)
    R - W-B
    Transfer L4 signal
    Ignition switch ON
    Transfer position switch H4F or H4L
    10 to 14 V
    Ignition switch ON
    Transfer position switch L4L
    Below 1.5 V
    F46-2 (HM1) - F46-4 (GND)
    B - W-B
    High-low transfer shift actuator motor
    Ignition switch ON
    Transfer position switch H4L → L4L (During operation of high-low transfer shift actuator motor from HIGH to LOW)
    10 to 14 V
    Ignition switch ON
    Transfer position switch H4L → L4L (High-low transfer shift actuator motor stopped)
    Below 1.5 V
    F46-3 (IG) - F46-4 (GND)
    R - W-B
    IG power
    Ignition switch ON
    11 to 14 V
    F46-4 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F46-6 (HM2) - F46-4 (GND)
    W - W-B
    High-low transfer shift actuator motor
    Ignition switch ON
    Transfer position switch L4L → H4L (During operation of high-low transfer shift actuator motor from LOW to HIGH)
    10 to 14 V
    Ignition switch ON
    Transfer position switch L4L → H4L (High-low transfer shift actuator motor stopped)
    Below 1.5 V
    F46-7 (TM2) - F46-4 (GND)
    V - W-B
    Multi mode transfer shift actuator motor
    Ignition switch ON
    Transfer position switch H4L → H4F (During operation of multi mode transfer shift actuator motor from LOCK to FREE)
    10 to 14 V
    Ignition switch ON
    Transfer position switch H4L → H4F (Multi mode transfer shift actuator motor stopped)
    Below 1.5 V
    F46-8 (TM1) - F46-4 (GND)
    P - W-B
    Multi mode transfer shift actuator motor
    Ignition switch ON
    Transfer position switch H4F → H4L (During operation of multi mode transfer shift actuator motor from FREE to LOCK)
    10 to 14 V
    Ignition switch ON
    Transfer position switch H4F → H4L (Multi mode transfer shift actuator motor stopped)
    Below 1.5 V



  2. A086154E52
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbols)
    F47-19 (CANH) - F46-4 (GND)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON
    Text in Illustration 
    *1
    Waveform 1

    HINT:
    The waveform varies depending on the CAN communication signal.



  4. A086155E49
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbols)
    F47-20 (CANL) - F46-4 (GND)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON
    Text in Illustration 
    *1
    Waveform 2

    HINT:
    The waveform varies depending on the CAN communication signal.