Home › Drivetrain · VF2A TRANSFER / 4WD / AWD › TRANSFER SYSTEM

TRANSFER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK 4WD CONTROL ECU

C159461E09

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F47-2 (4WDL) - F46-4 (GND)
    L - W-B
    Transfer indicator switch (L4 position)
    Ignition switch ON
    Transfer shift lever position H2 or H4
    10.5 to 14 V
    Ignition switch ON
    Transfer shift lever position L4 or N
    Below 1.5 V
    F47-3 (4WD) - F46-4 (GND)
    B - W-B
    Transfer indicator switch (4WD position)
    Ignition switch ON
    Transfer shift lever position H2
    10.5 to 14 V
    Ignition switch ON
    Transfer shift lever position H4, L4 or N
    Below 1.5 V
    F47-9 (DL1) - F46-4 (GND)
    LG - W-B
    A.D.D. actuator limit switch
    Ignition switch ON
    Transfer shift lever position H2
    Below 1.5 V
    Ignition switch ON
    Transfer shift lever position H4, L4 or N
    10.5 to 14 V
    F47-10 (DL2) - F46-4 (GND)
    GR - W-B
    A.D.D. actuator limit switch
    Ignition switch ON
    Transfer shift lever position H2
    10.5 to 14 V
    Ignition switch ON
    Transfer shift lever position H4, L4 or N
    Below 1.5 V
    F47-15 (ADD) - F46-4 (GND)
    W - W-B
    A.D.D. detection switch
    Ignition switch ON
    Transfer shift lever position H2
    9.5 to 14 V
    Ignition switch ON
    Transfer shift lever position H4, L4 or N
    Below 1.5 V
    F47-16 (NP) - F46-4 (GND)
    R - W-B
    Transfer indicator switch (Neutral position)
    Ignition switch ON
    Transfer shift lever position N
    Below 1.5 V
    Ignition switch ON
    Transfer shift lever position not N
    10.5 to 14 V
    F47-19 (CANH) - F46-4 (GND)
    G - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation (See waveform 1)
    F47-20 (CANL) - F46-4 (GND)
    W - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation (See waveform 2)
    F47-21 (L4) - F46-4 (GND)
    R - W-B
    Transfer L4 signal
    Ignition switch ON
    Transfer shift lever position H2 or H4
    10 to 14 V
    Ignition switch ON
    Transfer shift lever position L4 or N
    Below 1.5 V
    F46-1 (DM1) - F46-4 (GND)
    B - W-B
    A.D.D. actuator motor
    Ignition switch ON
    Transfer shift lever position H2 → H4, L4 or N (During operation of A.D.D. actuator motor from FREE to LOCK)
    10 to 14 V
    Ignition switch ON
    Transfer shift lever position H2 → H4, L4 or N (A.D.D. actuator motor stopped)
    Below 1.5 V
    F46-3 (IG) - F46-4 (GND)
    R - W-B
    IG power
    Ignition switch ON
    11 to 14 V
    F46-4 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F46-5 (DM2) - F46-4 (GND)
    Y - W-B
    A.D.D. actuator motor
    Ignition switch ON
    Transfer shift lever position H4, L4 or N → H2 (During operation of A.D.D. actuator motor from LOCK to FREE)
    10 to 14 V
    Ignition switch ON
    Transfer shift lever position H4, L4 or N → H2 (A.D.D. actuator motor stopped)
    Below 1.5 V



  2. A086154E52
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbols)
    F47-19 (CANH) - F46-4 (GND)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON
    Text in Illustration 
    *1
    Waveform 1

    HINT:
    The waveform varies depending on the CAN communication signal.



  4. A086155E49
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbols)
    F47-20 (CANL) - F46-4 (GND)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON
    Text in Illustration 
    *1
    Waveform 2

    HINT:
    The waveform varies depending on the CAN communication signal.