Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the Techstream, read the Data List.

    Driver Seat 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Reclining Rear
    Reclining switch signal (Rearward) / ON or OFF
    ON: Reclining switch (Rearward) on
    OFF: Reclining switch (Rearward) off
    -
    Reclining Front
    Reclining switch signal (Forward) / ON or OFF
    ON: Reclining switch (Forward) on
    OFF: Reclining switch (Forward) off
    -
    Front Vertical Down
    Front vertical switch signal (Downward) / ON or OFF
    ON: Front vertical switch (Downward) on
    OFF: Front vertical switch (Downward) off
    -
    Front Vertical Up
    Front vertical switch signal (Upward) / ON or OFF
    ON: Front vertical switch (Upward) on
    OFF: Front vertical switch (Upward) off
    -
    Lifter Switch Down
    Lifter switch signal (Downward) / ON or OFF
    ON: Lifter switch (Downward) on
    OFF: Lifter switch (Downward) off
    -
    Lifter Switch Up
    Lifter switch signal (Upward) / ON or OFF
    ON: Lifter switch (Upward) on
    OFF: Lifter switch (Upward) off
    -
    Slide Rear
    Sliding switch signal (Rearward) / ON or OFF
    ON: Sliding switch (Rearward) on
    OFF: Sliding switch (Rearward) off
    -
    Slide Front
    Sliding switch signal (Forward) / ON or OFF
    ON: Sliding switch (Forward) on
    OFF: Sliding switch (Forward) off
    -
    Seat Memory No1
    Seat position memorized with M1 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Seat Memory No2
    Seat position memorized with M2 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Seat Memory No3
    -
    -
    This item is not supported.
    Ignition Switch
    Communication state of engine switch signal / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    "OFF" is also displayed for this item when the engine switch is on (ACC).
    P Switch
    Shift lever position P signal / ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    -
    Parking Brake SW
    Parking brake switch status / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Vehicle Speed
    Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    Power Voltage
    Power supply for front power seat switch / min: 0.95 V, max: 20.84 V
    Within range of 11 to 14 V
    -
    Slide Position
    Seat sliding position / min: 0000, max: 65535
    Within range of 0 to 65535
    The displayed value decreases as the seat moves rearward.
    Reclining Position
    Seat reclining position / min: 0000, max: 65535
    Within range of 0 to 65535
    The displayed value decreases as the seat moves rearward.
    Front Vertical Position
    Seat front vertical position / min: 0000, max: 65535
    Within range of 0 to 65535
    The displayed value decreases as the seat moves downward.
    Lifter Position
    Seat lifter position / min: 0000, max: 65535
    Within range of 0 to 65535
    The displayed value decreases as the seat moves downward.
    Slide Pos Mem No1
    Seat sliding position memorized with M1 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Reclining Pos Mem No1
    Seat reclining position memorized with M1 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Frnt Vrtcl Pos Mem No1
    Front vertical position memorized with M1 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Lifter Pos Mem No1
    Lifter position memorized with M1 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Slide Pos Mem No2
    Seat sliding position memorized with M2 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Reclining Pos Mem No2
    Seat reclining position memorized with M2 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Frnt Vrtcl Pos Mem No2
    Front vertical position memorized with M2 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Lifter Pos Mem No2
    Lifter position memorized with M2 switch / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Slide Pos Mem No3
    -
    -
    This item is not supported.
    Reclining Pos Mem No3
    -
    -
    This item is not supported.
    Frnt Vrtcl Pos Mem No3
    -
    -
    This item is not supported.
    Lifter Pos Mem No3
    -
    -
    This item is not supported.
    Motor Status
    State of motor control/STANDBY, MOVING or LOCK
    STANDBY: Slide, reclining, front vertical and lifter motor are idle.
    MOVING: Slide, reclining, front vertical or lifter motor is moving.
    LOCK: Slide, reclining, front vertical or lifter motor is locked.
    -
    Slide Position Init Flag
    Seat sliding limit position memory / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Slide Position Rear Limit
    Seat sliding position / min: 0000, max: 65535
    Within range of 0 to 65535
    -
    Shift P sw (PMN)
    Shift lever position P signal / ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    -
    Memory Button Buzzer Request
    Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG or REG WAIT
    OFF: Buzzer does not sound.
    MOVE: Request to sound buzzer when starting memory replay
    REGISTRY: Request to sound buzzer when starting memory registration
    CANCEL: Request to sound buzzer when canceling memory call registration
    REG NG: Request to sound buzzer when memory call registration not possible
    REG WAIT: Request to sound buzzer when starting memory call cabin scan.
    -
    Driver Seat Request Command
    Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET
    OFF: No instruction
    MEMORY: Request to memorize
    MEM MOV: Request to recall memory
    MEM SOD: Request to recall through memory call function
    RET MOV: Request to return
    AWY MOV: Request to move away
    AWY SOD: Request to recall away position memory
    MEM AWY: Request to recall memorized position of seat
    MEM RET: Request to restore seat to memorized position
    -
    Driver Seat POS REQ
    Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3
    OFF: No operation
    MEM1: M1 switch operation status
    MEM2: M2 switch operation status
    MEM3: Related switch does not exist.
    DRV1: Memory call 1 function operating
    DRV2: Memory call 2 function operating
    DRV3: Related function does not exist.
    -
    Away Move Range Scale
    Driver seat slide away distance / NONE, SMALL, STANDARD or LONG
    NONE: No movement
    SMALL: Moves short distance.
    STANDARD: Moves standard distance.
    LONG: Moves long distance.
    -
    Return Move
    Return destination / AVAIL or NOT AVL
    AVAIL: Return destination set
    NOT AVL: Return destination not set
    -
    Return & Away Function
    Power easy access system status / AVAIL or NOT AVL
    AVAIL: Power easy access system functioning
    NOT AVL: Power easy access system not functioning
    -
    Driver Seat Buckle SW
    Status of driver seat belt / ON or OFF
    ON: Tongue plate engaged
    OFF: Tongue plate not engaged
    -
    Return Position
    Slide return position / min.: 0000, max.: 65535
    Within range of 0 to 65535
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0, Max.: 255
    Number of DTCs stored
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Driver Seat / Active Test.

  5. According to the display on the Techstream, perform the Active Test.

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front / OFF / Rear
    -
    Front Vertical Operation
    Seat front vertical operation
    Up / OFF / Down
    -
    Lifter Operation
    Seat lifter operation
    Up / OFF / Down
    -
    Seat Slide Operation
    Seat sliding operation
    Front / OFF / Rear
    -
    Buzzer
    Buzzer operation
    ON / OFF
    -