Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR

STEERING GEAR > REASSEMBLY

for Preparation Click here



1. INSTALL STEERING RACK END SUB-ASSEMBLY
  1. Temporarily install the 2 steering rack ends to the steering rack.

  1. Fill up the ball joints of the steering rack ends with MP grease.



    C215762E01
  1. Using SST, install the steering rack end (RH side) to the steering rack.

    SST
    09922-10010  

    Torque:
    without SST:
    105 N*m{ 1071 kgf*cm , 77 ft.*lbf }
    with SST:
    77 N*m{ 784 kgf*cm , 57 ft.*lbf }

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Hold
    *b
    Turn

    HINT:
    1. Rotate SST in the direction shown in the illustration.
    2. Use a torque wrench with a fulcrum length of 400 mm (15.75 in.).

  1. Using SST and a wrench, install the steering rack end (LH side) to the steering rack.

    SST
    09922-10010  

    Torque:
    without SST:
    105 N*m{ 1071 kgf*cm , 77 ft.*lbf }
    with SST:
    77 N*m{ 784 kgf*cm , 57 ft.*lbf }

    HINT:
    1. Rotate SST in the direction shown in the illustration.
    2. Use a torque wrench with a fulcrum length of 400 mm (15.75 in.).



2. INSTALL NO. 2 STEERING RACK BOOT


    C100988
  1. Apply silicon grease to the inside of the small opening of the boot.

  1. Install the 2 boots to the groove on the rack housing.



3. INSTALL NO. 1 STEERING RACK BOOT

HINT:
Use the same procedures described for No. 2 boot.



4. INSTALL STEERING RACK BOOT CLAMP RH


    C124255E03
  1. Using SST, install a new boot clamp as shown in the illustration.

    SST
    09521-24010  

    Standard clearance:
    3.0 mm (0.118 in.) or less

    NOTICE:
    Be careful not to damage the boot.



5. INSTALL STEERING RACK BOOT CLAMP LH

HINT:
Use the same procedures described for the RH side.



6. INSTALL STEERING RACK BOOT CLIP RH


    C178954E02
  1. Using pliers, install the boot clip.
    Text in Illustration 
    *a
    Upward
    *b
    180°
    V100135
    Front of Vehicle

    NOTICE:
    Make sure that the claws of the clip are positioned within the area shown in the illustration.



7. INSTALL STEERING RACK BOOT CLIP LH

HINT:
Use the same procedures described for the RH side.



8. INSTALL STEERING GEAR OUTLET RETURN TUBE
  1. Using a union nut wrench, install the return tube to the steering gear.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



9. INSTALL TURN PRESSURE TUBE
  1. Apply steering fluid to 2 new O-rings. Using a union nut wrench, install the 2 O-rings and turn pressure tube LH.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    HINT:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Apply steering fluid to 2 new O-rings. Using a union nut wrench, install the 2 O-rings and turn pressure tube RH.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    HINT:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



10. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Align the matchmarks of the tie rod and rack end, and temporarily install the tie rod with the lock nut.

    HINT:
    After adjusting toe-in, tighten the lock nut.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



11. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.