Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 1 COOLER THERMISTOR


E197775E01

NOTICE:
If reusing the evaporator, do not insert the thermistor into a location where the thermistor was previously inserted.

  1. Insert the thermistor to a location that is 1 fin to the right or left of its previous location.

    Standard:
    Item
    Specified Condition
    a
    50 mm (1.97 in.)
    b
    46.7 mm (1.84 in.)
    c
    33.3 mm (1.31 in.)
    d
    154.1 mm (6.07 in.)
    e
    25 mm (0.98 in.)

    Text in Illustration 
    *1
    1 Fin



2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the evaporator.



    E199284
  1. Install the evaporator.

  1. Attach the 4 claws to install the unit case.

  1. Install the 6 screws.



3. INSTALL DAMPER SERVO SUB-ASSEMBLY LH


  1. Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.


    E197776E01


    Text in Illustration 
    *A
    for Automatic Air Conditioning System
    -
    -
    *a
    Air Conditioning Unit Side
    *b
    Damper Servo Side

  1. Install the 4 screws.



4. INSTALL DAMPER SERVO SUB-ASSEMBLY RH


  1. Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.


    E197777E01


    Text in Illustration 
    *a
    Air Conditioning Unit Side
    *b
    Damper Servo Side

  1. Install the 3 screws.



5. INSTALL COOLER EXPANSION VALVE
  1. Install the expansion valve.



6. INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the air conditioning tube and accessory assembly.

  1. Install the air conditioning tube and accessory assembly.

  1. Using a 4 mm hexagon wrench, install the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Install new butyl tape.

  1. Install new packing.



7. INSTALL AIR CONDITIONING HARNESS
  1. Attach the clamps to install the harness.

  1. Connect the connectors.



8. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
  1. Install the radiator.

  1. Install the bracket with the 2 screws.



9. INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)
  1. Attach the 2 clamps to install the quick heater.

  1. Install the 2 screws.



10. INSTALL DRAIN COOLER HOSE


    E197396
  1. Install the drain cooler hose as shown in the illustration.



11. INSTALL ASPIRATOR HOSE
  1. Attach the 2 claws to install the aspirator hose.



12. INSTALL DEFROSTER NOZZLE ASSEMBLY
  1. Attach the 6 claws to install the defroster nozzle assembly.



13. INSTALL BLOWER ASSEMBLY
  1. Attach the 2 claws to install the blower assembly.

  1. Install the screw.

    Torque:
    2.7 N*m{ 28 kgf*cm , 24 in.*lbf }