Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM

CLIMATE CONTROL SEAT SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH


    B245520E28
  1. Disconnect the b24 seat heater control sub-assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b24-6 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b24-1 (SWL) - b24-6 (E)
    Engine switch on (IG)
    Refreshing seat switch LH side off
    Below 1 V
    Engine switch on (IG)
    Refreshing seat switch LH side on
    11 to 14 V
    b24-4 (B) - b24-6 (E)
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Heater Control Sub-assembly LH)
    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the b24 seat heater control sub-assembly LH connector.



    B241897E19
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b24-5 (THL) - Body ground
    Engine switch on (IG)
    Refreshing seat switch LH on, MIN → MAX
    Gradual increase between value below 1 V and value from 11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Seat Heater Control Sub-assembly LH)
    If the result is not as specified, the seat heater control sub-assembly LH may have a malfunction.



2. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH


    B245520E29
  1. Disconnect the a15 seat heater control sub-assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a15-6 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a15-1 (SWR) - a15-6 (E)
    Engine switch on (IG)
    Refreshing seat switch RH side off
    Below 1 V
    Engine switch on (IG)
    Refreshing seat switch RH side on
    11 to 14 V
    a15-4 (B1) - a15-6 (E)
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Heater Control Sub-assembly RH)
    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the a15 seat heater control sub-assembly LH connector.



    B241897E20
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a15-5 (THR) - Body ground
    Engine switch on (IG)
    Refreshing seat switch RH side on, MIN → MAX
    Gradual increase between value below 1 V and value from 11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Seat Heater Control Sub-assembly RH)
    If the result is not as specified, the seat heater control sub-assembly LH may have a malfunction.