Home › Audio / Visual / Telematics › AUDIO / VIDEO › LUGGAGE SPEAKER

LUGGAGE SPEAKER > INSTALLATION

for Preparation Click here



1. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Install the stereo component amplifier to the No. 1 speaker assembly with box with the 3 bolts.



2. INSTALL NO. 1 SPEAKER ASSEMBLY WITH BOX


    B240334
  1. Attach the 2 claws, lower the No. 1 speaker assembly with box in the direction of the arrow and set it in place.

  1. Install the No. 1 speaker assembly with box with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

  1. Connect the 5 connectors.



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. w/o Rear No. 2 Seat:

    1. Connect each connector.

    2. Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.

    3. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.

    4. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.

    5. Install the 3 bolts and screw.

    6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear No. 2 Seat:

    1. Connect each connector.

    2. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.

    3. Install the 3 bolts and screw.

    4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    5. Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



5. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL FRONT DECK SIDE TRIM COVER LH
  1. Attach the 2 claws to install the front deck side trim cover LH.



7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
  1. Push in the No. 1 luggage compartment trim hook to install it.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim hook.



8. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
  1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



9. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)
  1. Attach the 4 claws to install the rear floor carpet assembly.



10. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
  1. Attach the 5 clips to install the rear floor mat rear support plate.



11. INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)
  1. Install the inner floor side rail sub-assembly with the 4 bolts.



12. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 2 guides to install the deck board assembly.

  1. Install the 6 bolts.



13. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:
Use the same procedure as for the LH side.



14. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)
  1. Attach the 4 clips and 2 guides to install the luggage compartment side cover sub-assembly LH.



15. INSTALL NO. 2 REAR FLOOR BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 3 clips to install the rear No. 2 floor board assembly.



16. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)
  1. Attach the 2 clips and 2 guides to install the No. 2 deck board sub-assembly.



17. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



18. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
  1. Attach the clip to install the No. 1 deck board sub-assembly.



19. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)
  1. Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.

  1. Attach the 4 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim cover.



20. INSTALL OUTER LAP BELT ANCHOR COVER
  1. Attach the 3 claws to install the outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other outer lap belt anchor cover.



21. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



22. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



23. INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.



24. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
  1. Attach the 2 claws to install the rear No. 1 floor step cover.

    HINT:
    Use the same procedure for all the rear No. 1 floor step covers.