Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here


HINT:
When installing the symbol emblem, No. 1 back door emblem and No. 1 roof side mark, heat the vehicle body, symbol emblem, No. 1 back door emblem and No. 1 roof side mark using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Symbol Emblem
20 to 30°C (68 to 86°F)
No. 1 Back Door Emblem
20 to 30°C (68 to 86°F)
No. 1 Roof Side Mark
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, symbol emblem, No. 1 back door emblem or No. 1 roof side mark excessively.



1. INSTALL SYMBOL EMBLEM
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



    B239327E01
  1. Install a new symbol emblem.

    1. Using a heat light, heat the vehicle body and a new symbol emblem.

    2. Remove the peeling paper from the face of the symbol emblem.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Align the boss positions to install the symbol emblem.

      HINT:
      Press the symbol emblem firmly to install it.

      Text in Illustration 
      *1
      Boss



2. INSTALL NO. 1 BACK DOOR EMBLEM
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install a new No. 1 back door emblem.

    1. Using a heat light, heat the vehicle body and a new No. 1 back door emblem.

    2. Remove the peeling paper from the face of the No. 1 back door emblem.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    3. Install the No. 1 back door emblem in the position shown in the installation.


      B353452E01


      Text in Illustration 
      *a
      Reference Value
      -
      -

      Reference Measurement:

      Area
      Measurement
      Area
      Measurement
      A
      105.0 mm (4.134 in.)
      B
      104.0 mm (4.094 in.)
      C
      11.8 mm (0.465 in.)
      D
      17.5 mm (0.689 in.)
      E
      10.5 mm (0.413 in.)
      F
      6.0 mm (0.236 in.)
      G
      4.0 mm (0.157 in.)
      H
      7.0 mm (0.276 in.)
      I
      5.5 mm (0.217 in.)
      -
      -



3. INSTALL NO. 1 ROOF SIDE MARK
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install a new No. 1 roof side mark.

    1. Using a heat light, heat the vehicle body and a new No. 1 roof side mark.

    2. Remove the peeling paper from the face of the No. 1 roof side mark.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    3. Install the No. 1 roof side mark in the position shown in the installation.


      B239419E02


      Text in Illustration 
      *a
      Reference Value
      *b
      Over Fender End Line

      Reference Measurement:

      Area
      Measurement
      Area
      Measurement
      A
      95.0 mm (3.740 in.)
      B
      122.1 mm (4.807 in.)
      C
      346.6 mm (13.646 in.)
      D
      371.0 mm (14.606 in.)
      E
      157.3 mm (6.193 in.)
      F
      105.2 mm (4.142 in.)
      G
      370.9 mm (14.602 in.)
      H
      79.6 mm (3.134 in.)
      I
      149.4 mm (5.882 in.)
      J
      346.7 mm (13.650 in.)
      K
      346.9 mm (13.657 in.)
      L
      141.5 mm (5.571 in.)
      M
      87.7 mm (3.453 in.)
      -
      -