Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

E195784E10

  1. Disconnect the B38, F50 and F51 ECM connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F51-24 (BATT) - Body ground
    L - Body ground
    Power source circuit
    Always
    11 to 14 V
    F50-21 (IGSW) - Body ground
    W - Body ground
    IG power source circuit
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    F51-8 (ST1-) - Body ground
    B - Body ground
    Stop light switch signal circuit
    Ignition switch ON, brake pedal released
    11 to 14 V
    Ignition switch ON, brake pedal depressed
    Below 1 V
    F50-18 (STP) - Body ground
    V - Body ground
    Stop light switch signal circuit
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V
    F50-11 (CCS) - Body ground
    B - Body ground
    Cruise control switch circuit
    Cruise control switch on
    Below 2.5 Ω
    Cruise control switch off
    1 MΩ or higher
    +RES switch held on
    235 to 245 Ω
    -SET switch held on
    617 to 643 Ω
    CANCEL switch held on
    1509 to 1571 Ω
    B38-12 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the B38, F50 and F51 ECM connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B36-27 (D) - Body ground
    B - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in D
    11 to 14 V
    Ignition switch ON, shift lever not in D
    Below 1 V
    B36-29 (N) - Body ground
    G - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in N
    11 to 14 V
    Ignition switch ON, shift lever not in N
    Below 1 V
    B36-28 (R) - Body ground
    R - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    B36-35 (P) - Body ground
    L - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in P
    11 to 14 V
    Ignition switch ON, shift lever not in P
    Below 1 V
    F50-24 (S) - Body ground
    V - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S
    11 to 14 V
    Ignition switch ON, shift lever not in S
    Below 1 V
    F50-16 (SFTU) - Body ground
    GR - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S → shift lever moved to "+"
    11 to 14 V → Below 1 V
    F50-22 (SFTD) - Body ground
    LG - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S → shift lever moved to "-"
    11 to 14 V → Below 1 V
    If the result is not as specified, the ECM may be malfunctioning.