Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Cruise Control / Data List.

  5. According to the display on the Techstream, read the Data List.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
    Actual vehicle speed displayed
    -
    CCS Mem Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
    Vehicle speed stored in memory
    -
    Throttle Opening Angle
    Required throttle opening amount / Min.: 0°, Max.: 124.5°
    Required throttle opening angle
    -
    Cruise Control
    Cruise control / ON or OFF
    ON: Cruise control set
    OFF: Cruise control not set
    -
    Main SW M-CPU
    Cruise control switch (Main CPU) / ON or OFF
    ON: Cruise control switch on
    OFF: Cruise control switch off
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / ON or OFF
    ON: Cruise control switch on
    OFF: Cruise control switch off
    -
    CCS Indicator M-CPU
    Cruise main indicator (Main CPU) / ON or OFF
    ON: Cruise main indicator light on
    OFF: Cruise main indicator light off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -SET switch signal / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    +RES switch signal / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -
    Stp Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Operation Status
    Shift lever position signal / ON or OFF
    ON: Shift lever in D
    OFF: Shift lever not in D
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other item to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  5. According to the display on the Techstream, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    Cruise main indicator light
    ON/OFF
    -
    Indicat. SET
    SET indicator light
    ON/OFF
    -