Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY

REAR NO. 2 SEAT ASSEMBLY > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. REMOVE REAR SEAT CAP


    B240438
  1. Remove the 2 caps.



2. REMOVE REAR SEAT LOWER CUSHION HINGE COVER LH


    B237376
  1. Remove the 2 screws.

  1. Detach the 3 claws and remove the cover.



3. REMOVE REAR SEAT LOWER CUSHION HINGE COVER RH


    B238682E01
  1. Remove the 2 screws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.



4. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


B241710
  1. Using a T45 "TORX" socket wrench, remove the bolt and inner belt assembly.



5. REMOVE REAR NO. 1 SEAT CUSHION MOULDING


    B236519E01
  1. Using a clip remover, remove the 2 clips.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and 4 guides and remove the moulding.



6. REMOVE SEAT CUSHION COVER WITH PAD


    B239925E01
  1. Detach the 2 fasteners.
    Text in Illustration 
    *1
    Fastener



    B239926E01
  1. Open the 2 fasteners.
    Text in Illustration 
    *1
    Fastener



    B236671
  1. Using a clip remover, remove the 2 clips and open the under part of the seat cushion cover.



    B239927E01
  1. Detach the 2 hooks.
    Text in Illustration 
    *1
    Hook



    B239928E01
  1. Detach the 2 hooks and remove the seat cushion cover with pad.
    Text in Illustration 
    *1
    Hook



7. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B236523E01
  1. Detach the fastener.
    Text in Illustration 
    *1
    Fastener

  1. Remove the 2 hog rings and seat cushion cover.



8. REMOVE REAR NO. 2 SEAT CUSHION PROTECTOR


    B236571E01
  1. Cut off the 5 tack pins and remove the protector from the seat cushion pad.
    Text in Illustration 
    *1
    Tack Pin



9. REMOVE REAR NO. 2 SEAT CUSHION MOULDING


    B237377
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the moulding.



10. REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
  1. Operate the seat track lock lever and retract the seat cushion frame.



    B237378
  1. Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seat cushion frame.



11. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH


    B237381E01
  1. Remove the 3 clips.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and 4 guides and remove the 3rd seat link.



12. REMOVE SEAT TRACK LOCK LEVER


    B237379E01
  1. Detach the clamp.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the cable end in the direction indicated by the arrow and disconnect the cable.



    B237380E01
  1. Remove the screw.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 guides and remove the lever.



13. REMOVE REAR SEAT LEG COVER LH


    B237382E01
  1. Remove the clip.
    Text in Illustration 
    *1
    Hook

  1. Detach the 3 hooks and 5 clips and remove the cover.



14. REMOVE REAR NO. 3 SEAT LEG COVER LH


    B239683
  1. Detach the 2 claws and remove the cover.



15. REMOVE REAR SEAT CUSHION INNER HINGE COVER LH


    B237383E01
  1. Remove the screw and clip.
    Text in Illustration 
    *1
    Guide

  1. Detach the guide and remove the cover.



16. REMOVE REAR SEAT CUSHION INNER HINGE COVER RH


    B237384E01
  1. Remove the screw and clip.
    Text in Illustration 
    *1
    Guide

  1. Detach the guide and remove the cover.



17. REMOVE REAR SEAT LOCK CONTROL CABLE LH


    B240106E01
  1. Detach the clamp.
    Text in Illustration 
    *1
    Clamp
    *2
    Cable End

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.



18. REMOVE REAR NO. 1 SEATBACK LOCK STRIKER COVER


    B237385E01
  1. Using a screwdriver, detach the claw and guide and remove the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Guide



19. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    B237386E01
  1. Remove the 2 screws.
    Text in Illustration 
    *1
    Clamp
    *2
    Cable End
    *3
    Guide

  1. Detach the guide and remove the lever.

  1. Detach the clamp.

  1. Twist the cable end in the direction indicated by the arrow and disconnect the cable.



20. REMOVE ROPE HOOK ASSEMBLY


    B237387
  1. Using a screwdriver, detach the 2 claws and open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B237388
  1. Remove the bolt and rope hook assembly.



21. REMOVE REAR NO. 2 SEATBACK LOCK STRIKER COVER


    B237395E01
  1. Using a screwdriver, detach the claw and guide and remove the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Guide



22. REMOVE REAR SEAT LOCK RELEASE LEVER ASSEMBLY


    B237397E01
  1. Remove the 2 screws.
    Text in Illustration 
    *1
    Hook

  1. Detach the hook and remove the lever.



    B237396E01
  1. Detach the 2 clamps.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the 2 cable ends in the direction indicated by the arrow and disconnect the 2 cables.



23. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B237398
  1. Detach the 7 clips and remove the board.



24. REMOVE REAR SEATBACK LOCK HOOK


    B238697
  1. Remove the lock hook.



25. REMOVE REAR SEAT NO. 1 COVER BEZEL


    B238696E01
  1. Remove the 2 screws, detach the guide and remove the bezel.
    Text in Illustration 
    *1
    Guide



26. REMOVE SEATBACK COVER WITH PAD


    B237401E01
  1. Detach the hooks.
    Text in Illustration 
    *1
    Hook



    B238699
  1. Detach the 8 clips and remove the seatback cover with pad.



27. REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH


    B236581
  1. Remove the 7 hog rings and seatback cover.



28. REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR


    B236572E01
  1. Cut off the 5 tack pins and remove the protector from the seatback pad.
    Text in Illustration 
    *1
    Tack Pin



29. REMOVE REAR SEAT HEADREST COVER


    B237402
  1. Remove the 2 screws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.



30. REMOVE REAR SEAT HEADREST CABLE


    B236550E01
  1. Detach the 2 clamps.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.



31. REMOVE REAR SEAT HEADREST ASSEMBLY


    B237403
  1. Remove the 3 nuts and headrest.



32. REMOVE REAR NO. 3 SEAT PROTECTOR LH


    B236541
  1. Detach the 4 claws and remove the 2 protectors.



33. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH


    B240113
  1. Detach the 4 claws and remove the cover.



34. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH


    B237399E01
  1. Remove the screw.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.



35. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER RH


    B238702
  1. Detach the 5 claws and remove the cover.



36. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER RH


    B237400E01
  1. Remove the screw.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.



37. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY


    B237372E01
  1. Detach the 2 clamps.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the cable end in the direction indicated by the arrow and remove the strap.



38. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY (for RH Side)


    B237373E01
  1. Detach the 3 clamps and cut off the 2 cable ties.
    Text in Illustration 
    *1
    Cable End
    *2
    Cable Tie
    *3
    Clamp

  1. Twist the cable end in the direction indicated by the arrow and remove the strap.



39. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY


    B237374E01
  1. Remove the clamp labeled B and detach the 2 clamps labeled A.
    Text in Illustration 
    *1
    Clamp A
    *2
    Clamp B
    *3
    Cable Tie
    *4
    Cable End

  1. Cut off the 2 cable ties.

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.



40. REMOVE NO. 2 SEAT LOCK CABLE


    B237371E01
  1. Detach the clamp.
    Text in Illustration 
    *1
    Clamp
    *2
    Cable End

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.



41. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B240402
  1. Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.



42. REMOVE NO. 3 SEAT LEG ASSEMBLY LH


    B295838
  1. Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.