REAR NO. 2 SEAT ASSEMBLY > REASSEMBLY |
| 1. INSTALL NO. 3 SEAT LEG ASSEMBLY LH |
Install the seat cushion under carpet LH to the No. 3 seat leg assembly LH with the 4 clips.
| 2. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
Using a T45 "TORX" socket wrench, install the seatback frame with the 4 "TORX" bolts.
| 3. INSTALL NO. 2 SEAT LOCK CABLE |
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp |
| *2 | Cable End |
Attach the clamp to install the cable.
| 4. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp A |
| *2 | Clamp B |
| *3 | Cable Tie |
| *4 | Cable End |
Attach the 2 clamps labeled A to install the cable.
Install the clamp labeled B together with the No. 2 seat lock cable.
Install 2 new cable ties.
| 5. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY |
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Cable End |
| *2 | Clamp |
Attach the 2 clamps to install the strap.
| 6. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY (for RH Side) |
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Cable End |
| *2 | Clamp |
| *3 | Cable Tie |
Attach the 3 clamps to install the strap.
Install 2 new cable ties.
| 7. INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER RH |
Attach the 2 claws and guide to install the cover.
Install the screw.
| 8. INSTALL REAR NO. 2 SEAT INNER RECLINING COVER RH |
Attach the 5 claws to install the cover.
| 9. INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH |
Attach the 2 claws and guide to install the cover.
Install the screw.
| 10. INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH |
Attach the 4 claws to install the cover.
| 11. INSTALL REAR NO. 3 SEAT PROTECTOR LH |
Attach the 4 claws to install the 2 protectors.
| 12. INSTALL REAR SEAT HEADREST ASSEMBLY |
Install the headrest with the 3 nuts.
| 13. INSTALL REAR SEAT HEADREST CABLE |
![]() |
Twist the 2 cable ends in the direction indicated by the arrow to connect them.
| *1 | Cable End |
| *2 | Clamp |
Attach the 2 clamps to install the cable.
| 14. INSTALL REAR SEAT HEADREST COVER |
Attach the 2 claws and guide to install the cover.
Install the 2 screws.
| 15. INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR |
Install the protector to the seatback pad with 5 new tack pins.
| 16. INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the seatback cover to the seatback pad with 7 new hog rings.
| *1 | Hog Ring Pliers |
| 17. INSTALL SEATBACK COVER WITH PAD |
Attach the 8 clips.
Attach the hooks to install the seatback cover with pad.
| 18. INSTALL REAR SEAT NO. 1 COVER BEZEL |
Pass the strap through the bezel hole.
Attach the guide to install the bezel.
Install the 2 screws.
| 19. INSTALL REAR SEATBACK LOCK HOOK |
Install the lock hook.
| 20. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
Attach the 7 clips to install the board.
| 21. INSTALL REAR SEAT LOCK RELEASE LEVER ASSEMBLY |
![]() |
Twist the 2 cable ends in the direction indicated by the arrow to connect them.
| *1 | Cable End |
| *2 | No. 2 Seat Lock Cable |
| *3 | Fold Seat Lock Control Cable |
| *4 | Clamp |
Attach the 2 clamps.
Attach the hook to install the lever.
Install the 2 screws.
| 22. INSTALL REAR NO. 2 SEATBACK LOCK STRIKER COVER |
![]() |
Attach the guide and claw to install the cover.
| *1 | Guide |
| 23. INSTALL ROPE HOOK ASSEMBLY |
Install the rope hook with the bolt.
![]() |
Attach the 2 claws to close the cover.
| 24. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp |
| *2 | Cable End |
| *3 | Guide |
Attach the clamp.
Attach the guide to install the lever.
Install the 2 screws.
| 25. INSTALL REAR NO. 1 SEATBACK LOCK STRIKER COVER |
![]() |
Attach the guide and claw to install the cover.
| *1 | Guide |
| 26. INSTALL REAR SEAT LOCK CONTROL CABLE LH |
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp |
| *2 | Cable End |
Attach the clamp to install the cable.
| 27. INSTALL REAR SEAT CUSHION INNER HINGE COVER LH |
Attach the guide to install the cover.
Install the clip and screw.
| 28. INSTALL REAR SEAT CUSHION INNER HINGE COVER RH |
Attach the guide to install the cover.
Install the clip and screw.
| 29. INSTALL REAR NO. 3 SEAT LEG COVER LH |
Attach the 2 claws to install the cover.
| 30. INSTALL REAR SEAT LEG COVER LH |
Attach the 5 clips and 3 hooks to install the cover.
Install the clip.
| 31. INSTALL SEAT TRACK LOCK LEVER |
Attach the 2 guides.
Install the lever with the screw.
![]() |
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Cable End |
| *2 | Clamp |
Attach the clamp.
| 32. INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH |
Attach the 4 guides and 2 claws to install the link.
Install the 3 clips.
| 33. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH |
Using a T40 "TORX" socket wrench, install the seat cushion frame with the 4 "TORX" bolts.
Pull out the seat cushion frame.
| 34. INSTALL REAR NO. 2 SEAT CUSHION MOULDING |
Attach the 2 claws to install the moulding.
Install the 2 screws.
| 35. INSTALL REAR NO. 2 SEAT CUSHION PROTECTOR |
Install the protector to the seat cushion pad with 5 new tack pins.
| 36. INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 2 new hog rings.
| *1 | Fastener |
| *2 | Hog Ring Pliers |
Attach the fastener.
| 37. INSTALL SEAT CUSHION COVER WITH PAD |
Attach the 2 hooks to install the seat cushion cover with pad.
Attach the 2 hooks.
Install the 2 clips to close the cover.
Close the 2 fasteners.
Attach the 2 fasteners.
| 38. INSTALL REAR NO. 1 SEAT CUSHION MOULDING |
Attach the 4 guides and 2 claws to install the moulding.
Install the 2 clips.
| 39. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
Using a T45 "TORX" socket wrench, install the inner belt assembly with the bolt.
| 40. INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH |
Attach the guide and 2 claws to install the cover.
Install the 2 screws.
| 41. INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH |
Attach the 3 claws to install the cover.
Install the 2 screws.
| 42. INSTALL REAR SEAT CAP |
Install the 2 caps.