Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Multi-terrain Select Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

When the ON/OFF switch of the multi-terrain select switch is turned on, multi-terrain select control is enabled and the multi-terrain select indicator light illuminates.
After selecting a road surface type using the mode selector switch of the multi-terrain select switch, the system optimizes throttle control and brake fluid pressure control for wheels that slip when accelerating, which allows the power lost when the wheels slip during acceleration to be distributed to all 4 wheels.
The slip indicator light blinks while the system is operating.
The system can operate under the following conditions:
  1. The vehicle stability control system is normal.
  2. The vehicle speed is 12 km/h (7 mph) or less.
  3. Crawl control is not operating.
  4. The selected road surface is "Mud & Sand" and the transfer is set to H4 or L4, or the selected road surface is "Loose Rock", "Mogul" or "Rock" and the transfer is set to L4.
When there is a malfunction in the multi-terrain select system, the multi-terrain select indicator light blinks.

WIRING DIAGRAM


C214521E04


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS) (Click here)
OK


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.READ VALUE USING TECHSTREAM (OFF-ROAD GUIDANCE SWITCH (MULTI-TERRAIN SELECT SWITCH))
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Off-road Guidance Switch
    Multi-terrain select switch/ ON or OFF
    ON: Multi-terrain select switch on
    OFF: Multi-terrain select off
    -

    OK:
    The Techstream displays ON or OFF according to multi-terrain select switch operation.



NG
Go to step 4
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)  

4.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, +B, GND)
  1. Disconnect the U1 drive monitor switch connector.



    C217212E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    U1-6 (+B) - Body ground
    Always
    11 to 14 V
    U1-12 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U1-7 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Drive Monitor Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVE MONITOR SWITCH (Click here)