FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY |
| 1. REMOVE SEAT ADJUSTER COVER CAP |
![]() |
Remove the 2 seat adjuster cover caps.
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH |
![]() |
Raise the reclining adjuster release handle RH to reveal the claw. Using a screwdriver, detach the claw to remove the reclining adjuster release handle RH.
| *1 | Protective Tape |
| 3. REMOVE FRONT SEAT CUSHION SHIELD RH |
![]() |
Remove the screw.
Using a moulding remover, detach the 4 claws and clip, and then remove the front seat cushion shield RH.
| 4. REMOVE FRONT SEAT INNER CUSHION SHIELD RH |
![]() |
Using a moulding remover, detach the 4 claws to remove the front inner cushion shield RH.
| 5. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH |
for Driver Side:
Disconnect the connector and detach the 4 clamps.
for Passenger Side:
Disconnect the connector and detach the clamp.
![]() |
Remove the nut and front seat inner belt.
| 6. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
![]() |
Remove the rubber band from the separate type front seat cushion spring assembly.
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Detach the 2 hooks.
![]() |
Detach the claw to disconnect the airbag connector.
Detach the 3 airbag wire harness clamps.
Detach the fastening tape to disconnect the airbag wire harness.
| *1 | Fastening Tape |
![]() |
Remove the 4 bolts and separate type front seatback assembly.
| 7. REMOVE SEAT TRACK ADJUSTING HANDLE |
![]() |
Using a screwdriver, disengage the 2 springs to remove the seat track adjusting handle from the separate type front seat cushion spring assembly.
| 8. REMOVE FRONT SEAT LEG COVER RH |
![]() |
Detach the 2 claws.
Move the front seat leg cover RH in the direction of the arrow to remove the front seat leg cover RH.
| 9. REMOVE SEAT CUSHION COVER WITH PAD |
Detach each hook to remove the seat cushion cover with pad.

| 10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the 15 hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.
| 11. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Detach the claw and guide, and then remove the reclining adjuster inside cover RH.
| 12. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH |
![]() |
Remove the screw.
Move the front seat cushion edge protector RH in the direction of the arrow to detach the hook and remove the front seat cushion edge protector RH.
| 13. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH |
| 14. REMOVE OCCUPANT CLASSIFICATION ECU |
![]() |
Disconnect the 2 connectors.
Detach the claw and remove the occupant classification ECU.
| 15. REMOVE FRONT SEAT WIRE RH |
Remove the front seat wire RH.
| 16. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Detach the guide.
Move the reclining adjuster inside cover LH in the direction of the arrow to remove it.
| 17. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 18. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the 3 hog rings.
![]() |
Open the 2 fasteners and separate type front seatback cover.
![]() |
Remove the nut, detach the 2 hooks and disconnect the seatback cover bracket from the separate type front seatback spring assembly.
![]() |
Using a screwdriver, detach the 4 claws and remove the 2 front seat headrest supports.
Remove the seatback cover with pad from the separate type front seatback spring assembly.
| 19. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Disconnect the seatback cover bracket from the separate type front seatback pad.
![]() |
Remove the 13 hog rings and separate type front seatback cover from the separate type front seatback pad.
| 20. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY |
![]() |
Detach the 2 clamps to disconnect the front seat side airbag wire harness.
![]() |
Using an E10 "TORX" socket wrench, remove the 2 nuts and front seat side airbag assembly.