FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY |
| 1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY |
Using an E10 "TORX" socket wrench, install the front seat side airbag assembly with 2 new nuts.
Attach the 2 clamps to connect the front seat side airbag wire harness.
| 2. INSTALL NO. 2 SEAT WIRE |
Connect each connector and engage each clamp to install the No. 2 seat wire.
| 3. INSTALL SEATBACK CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System) |
Attach the 2 claws to install the seatback climate control duct LH.
| 4. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System) |
Install the seatback climate control blower LH with the 4 screws.
Connect the connector.
| 5. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Set the front seatback heater assembly LH in place with the name stamp side facing the separate type front seatback cover.
| *1 | Tack Pin |
| *2 | Name Stamp |
Install the front seatback heater assembly LH with 10 new tack pins.
| 6. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 13 new hog rings.
| *1 | Hog Ring Pliers |
![]() |
Connect the seatback cover bracket to the separate type front seatback pad.
| 7. INSTALL SEATBACK COVER WITH PAD |
w/o Climate Control Seat System:
Install the seatback cover with pad to the separate type front seatback spring assembly.
Attach the 4 claws to install the 2 front seat headrest supports.
Attach the 2 hooks and connect the seatback cover bracket to the separate type front seatback spring assembly with the nut.
Close the 2 fasteners and separate type front seatback cover.

| *A | for Cloth Seat | *B | for Leather Seat |
![]() |
Using hog ring pliers, install 3 new hog rings.
| *1 | Hog Ring Pliers |
w/ Climate Control Seat System:
Install the seatback cover with pad to the separate type front seatback spring assembly.
Attach the 4 claws to install the 2 front seat headrest supports.
Attach the 2 hooks and connect the seatback cover bracket to the separate type front seatback spring assembly with the nut.
![]() |
Using hog ring pliers, install 5 new hog rings.
| *1 | Hog Ring Pliers |
Attach the 7 hooks.
Connect the seat heater connector and attach the wire harness clamp.
| 8. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Attach the guide to install the reclining adjuster inside cover LH.
| 9. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
| 10. INSTALL FRONT SEAT WIRE LH |
Connect each connector and engage each clamp to install the front seat wire LH.
| 11. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
Attach the claw to install the occupant classification ECU.
Connect the 2 connectors.
| 12. INSTALL SEAT CUSHION CLIMATE CONTROL BRACKET LH (w/ Climate Control Seat System) |
Install the seat cushion climate control bracket LH with the 2 screws.
| 13. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System) |
Attach the 4 guides to install the seat cushion climate control blower assembly LH.
Connect the connector.
| 14. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System) |
Attach the 3 guides.
Attach the 2 claws to install the seat cushion climate control duct LH.
| 15. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
Attach the 2 clamps to install the seat heater control.
Connect the connector.
| 16. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH |
![]() |
Move the front seat cushion edge protector LH in the direction of the arrow to attach the hook and install the front seat cushion edge protector LH.
Install the screw.
| 17. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH |
| 18. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side) |
Attach the hook and clip to install the front seat lower cushion shield LH.
Install the screw.
| 19. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side) |
Attach the hook and clip to install the front seat lower cushion shield RH.
Install the screw.
| 20. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Attach the claw and guide to install the reclining adjuster inside cover LH.
| 21. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Set the front seat cushion heater assembly LH in place with the name stamp side facing the seat cushion cover.
| *1 | Tack Pin |
| *2 | Name Stamp |
Install the front seat cushion heater assembly LH with new 22 tack pins.
![]() |
Connect the wire harness to the separate type front seat cushion cover.
| 22. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.
| *1 | Hog Ring Pliers |
| 23. INSTALL SEAT CUSHION COVER WITH PAD |
Attach the each hook to install the seat cushion cover with pad.
w/ Seat Heater System:
Connect the seat heater connector and attach the 3 wire harness clamps.
| 24. INSTALL FRONT SEAT LEG COVER LH |
![]() |
Move the cover in the direction of the arrow to install the front seat leg cover LH.
Attach the 2 claws.
| 25. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
w/o Climate Control Seat System:
Install the seatback assembly with the 4 bolts.
Attach the fastening tape to connect the airbag wire harness.
Attach the 3 airbag wire harness clamps.
Attach the claw to connect the airbag connector.
Attach the 2 hooks.
Attach the clamp to connect the No. 2 seat wire.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
Install the rubber band to the seat cushion spring.
w/ Climate Control Seat System:
Install the seatback assembly with the 4 bolts.
Attach the fastening tape to connect the airbag wire harness.
Attach the 3 airbag wire harness clamps.
Attach the claw to connect the airbag connector.
Attach the 2 hooks.
Attach the clamp to connect the No. 2 seat wire.
Connect the seat heater connector and attach the wire harness clamp.
| 26. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Install the front seat inner belt with the nut.
| *a | Protruding Part |
for Driver Side:
Connect the connector and attach the 4 clamps.
for Passenger Side:
Connect the connector and attach the clamp.
| 27. INSTALL FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side) |
Attach the 3 claws to install the front seat inner cushion shield LH.
| 28. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side) |
Attach the 4 claws to install the front seat inner cushion shield RH.
| 29. INSTALL FRONT SEAT NO. 1 INNER CUSHION SHIELD LH |
![]() |
Attach the 2 claws to install the front seat No. 1 inner cushion shield LH.
| 30. INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side) |
![]() |
Connect the lumbar switch connector.
Attach the 2 claws to install the lumbar switch.
| 31. INSTALL FRONT POWER SEAT SWITCH LH |
Connect the power seat switch connector.
Install the power seat switch with the 3 screws.
| 32. INSTALL FRONT SEAT CUSHION SHIELD LH |
Attach the 3 wire harness clamps and connect the seat wire connector.

Attach the 3 claws to close the wire harness cover.
Connect the lifter motor connector.
Remove the clip attached to the separate type front seatback spring assembly and install it to the front seat cushion shield LH.
Attach the 2 clips, 3 claws and guide.
Attach the guide of the front seat No. 1 inner cushion shield LH and install the screw.
| 33. INSTALL RECLINING POWER SEAT SWITCH KNOB |
![]() |
Attach the 2 claws to install the reclining power seat switch knob.
| 34. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Attach the 2 claws to install the slide and vertical power seat switch knob.
| 35. INSTALL FRONT SEATBACK BOARD CLIP (w/ Climate Control Seat System) |
![]() |
Install the 2 new front seatback board clips to the front seatback board sub-assembly LH.
| 36. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Climate Control Seat System) |
![]() |
Attach the 2 guides and 2 claws of the front seatback board clip to install the seatback board sub-assembly LH.
Attach the 2 hooks to connect the 2 rubber bands.
| 37. INSTALL SEAT ADJUSTER COVER CAP |
Install the 2 seat adjuster cover caps.