Home › Vehicle Interior › SEAT › POWER SEAT SWITCH

POWER SEAT SWITCH > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER SEAT SWITCH LH


B239569E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Slide Switch:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (SLDF) - 8 (B)
    5 (SLDF) - 7 (B2)
    Front
    Below 1 Ω
    2 (SLDR) - 11 (E)
    2 (SLDR) - 12 (E1)
    5 (SLDF) - 11 (E)
    5 (SLDF) - 12 (E1)
    Off
    2 (SLDR) - 11 (E)
    2 (SLDR) - 12 (E1)
    5 (SLDF) - 11 (E)
    5 (SLDF) - 12 (E1)
    Rear
    2 (SLDR) - 8 (B)
    2 (SLDR) - 7 (B2)
    Front Vertical Switch:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (FUP) - 8 (B)
    1 (FUP) - 7 (B2)
    Up
    Below 1 Ω
    6 (FDWN) - 11 (E)
    6 (FDWN) - 12 (E1)
    1 (FUP) - 11 (E)
    1 (FUP) - 12 (E1)
    Off
    6 (FDWN) - 11 (E)
    6 (FDWN) - 12 (E1)
    1 (FUP) - 11 (E)
    1 (FUP) - 12 (E1)
    Down
    6 (FDWN) - 8 (B)
    6 (FDWN) - 7 (B2)
    Lifter Switch:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (LUP) - 8 (B)
    3 (LUP) - 7 (B2)
    Up
    Below 1 Ω
    4 (LDWN) - 11 (E)
    4 (LDWN) - 12 (E1)
    3 (LUP) - 11 (E)
    3 (LUP) - 12 (E1)
    Off
    4 (LDWN) - 11 (E)
    4 (LDWN) - 12 (E1)
    3 (LUP) - 11 (E)
    3 (LUP) - 12 (E1)
    Down
    4 (LDWN) - 8 (B)
    4 (LDWN) - 7 (B2)
    Reclining Switch:
    Tester Connection
    Switch Condition
    Specified Condition
    10 (RCLF) - 8 (B)
    10 (RCLF) - 7 (B2)
    Front
    Below 1 Ω
    9 (RCLR) - 11 (E)
    9 (RCLR) - 12 (E1)
    10 (RCLF) - 11 (E)
    10 (RCLF) - 12 (E1)
    Off
    9 (RCLR) - 11 (E)
    9 (RCLR) - 12 (E1)
    10 (RCLF) - 11 (E)
    10 (RCLF) - 12 (E1)
    Rear
    9 (RCLR) - 8 (B)
    9 (RCFR) - 7 (B2)

    If the result is not as specified, replace the front power seat switch.
    Text in Illustration 
    *1
    Front Vertical Switch
    *2
    Slide Switch
    *3
    Lifter Switch
    *4
    Reclining Switch
    *a
    Component without harness connected
    (Front Power Seat Switch)



2. INSPECT FRONT POWER SEAT SWITCH RH


B241813E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Slide Switch:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (SLDF) - 13 (B)
    Front
    Below 1 Ω
    5 (SLDR) - 10 (E)
    2 (SLDF) - 10 (E)
    Off
    5 (SLDR) - 10 (E)
    2 (SLDF) - 10 (E)
    Rear
    5 (SLDR) - 13 (B)
    Reclining Switch:
    Tester Connection
    Switch Condition
    Specified Condition
    11 (RCLF) - 13 (B)
    Front
    Below 1 Ω
    12 (RCLR) - 10 (E)
    11 (RCLF) - 10 (E)
    Off
    12 (RCLR) - 10 (E)
    11 (RCLF) - 10 (E)
    Rear
    12 (RCLR) - 13 (B)

    If the result is not as specified, replace the front power seat switch.
    Text in Illustration 
    *1
    Slide Switch
    *2
    Reclining Switch
    *a
    Component without harness connected
    (Front Power Seat Switch)