Home › Vehicle Interior › SEAT › FRONT SEAT CUSHION HEATER

FRONT SEAT CUSHION HEATER > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH


    B239184E02
  1. Set the front seat cushion heater assembly LH in place with the name stamp side facing the seat cushion cover.
    Text in Illustration 
    *1
    Tack Pin
    *2
    Name Stamp

  1. Install the front seat cushion heater assembly LH with new 22 tack pins.



    B247951
  1. Connect the wire harness to the separate type front seat cushion cover.



2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


B239183E01
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



3. INSTALL SEAT CUSHION COVER WITH PAD
  1. Attach the 7 hooks to install the seat cushion cover with pad.

  1. Connect the seat heater connector and attach the 3 wire harness clamps.

  1. Attach the 2 hooks.

  1. Attach the fastening tape to connect the airbag wire harness.

  1. Connect the seat heater connector and attach the wire harness clamp.

  1. w/o Climate Control Seat System:
    Install the rubber band to the separate type front seat cushion spring assembly.



4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    B241692E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    Text in Illustration 
    *a
    Protruding Part

  1. for Driver Side:
    Connect the connector and attach the 4 clamps.

  1. for Passenger Side:
    Connect the connector and attach the clamp.



5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)
  1. Attach the 3 claws to install the front seat inner cushion shield LH.



6. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
  1. Attach the 4 claws to install the front seat inner cushion shield RH.



7. INSTALL FRONT SEAT CUSHION SHIELD LH


  1. Attach the 3 wire harness clamps and connect the seat wire connector.


    B239535

  1. Attach the 3 claws to close the wire harness cover.

  1. Connect the lifter motor connector.

  1. Remove the clip attached to the separate type front seatback spring assembly and install it to the front seat cushion shield LH.

  1. Attach the 2 clips, 3 claws and guide.

  1. Attach the guide of the front seat No. 1 inner cushion shield LH and install the screw.



8. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Climate Control Seat System)


    B360695
  1. Attach the 2 guides and 2 claws of the front seatback board clip to install the seatback board sub-assembly LH.

  1. Attach the 2 hooks to connect the 2 rubber bands.



9. INSTALL FRONT SEAT ASSEMBLY
(Click here)