Home › Vehicle Interior › SEAT › FRONT SEAT CUSHION HEATER

FRONT SEAT CUSHION HEATER > REMOVAL

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT SEAT ASSEMBLY
(Click here)


2. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Climate Control Seat System)


    B357316
  1. Detach the 2 hooks and disconnect the 2 rubber bands.



    B360690E01
  1. Apply protective tape to the locations shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B360691E01
  1. Insert a screwdriver in the clearance between the front seatback board sub-assembly LH and separate type front seatback assembly.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Point (A)

  1. Place the screwdriver at point (A) shown in the illustration and move the screwdriver in the direction of the arrow to detach the 2 guides and remove the 2 seatback board clips from the front seatback board sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.



    B360692
  1. Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 guides and remove the front seatback board sub-assembly LH.



3. REMOVE FRONT SEAT CUSHION SHIELD LH


  1. Remove the screw of the front seat No. 1 inner cushion shield LH and detach the guide.


    B239534

  1. Using a moulding remover, detach the 3 claws and guide.

  1. Move the front seat cushion shield LH in the direction of the arrow to detach the clip and remove the front seat No. 1 inner cushion shield LH together with the front seat cushion shield LH as a unit.

  1. Detach the clip of the front seat No. 1 inner cushion shield LH.

  1. Disconnect the lifter motor connector.



    B239536
  1. Detach the 3 claws and open the wire harness cover.

  1. Detach the 3 wire harness clamps and disconnect the seat wire connector.



4. REMOVE FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)


    B239167
  1. Using a moulding remover, detach the 3 claws and remove the front seat inner cushion shield LH.



5. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)


B239169
  1. Using a moulding remover, detach the 4 claws and remove the front seat inner cushion shield RH.



6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. for Driver Side:
    Disconnect the connector and detach the 4 clamps.

  1. for Passenger Side:
    Disconnect the connector and detach the clamp.



    B241691
  1. Remove the nut and front seat inner belt.



7. REMOVE SEAT CUSHION COVER WITH PAD


    B239173
  1. w/o Climate Control Seat System:
    Remove the rubber band from the separate type front seatback spring assembly.



    B241810
  1. Disconnect the seat heater connector and detach the wire harness clamp.



    B241812E01
  1. Detach the fastening tape to disconnect the airbag wire harness.
    Text in Illustration 
    *1
    Fastening Tape



    B239177
  1. Detach the 2 hooks.



    B241811
  1. Disconnect the seat heater connector and detach the 3 wire harness clamps.



  1. Detach each hook to remove the seat cushion cover with pad.


    B239180



8. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


B239182
  1. Remove the 15 hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.



9. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH


    B247952
  1. Disconnect the wire harness from the separate type front seat cushion cover.



    B239184E01
  1. Cut off the 22 tack pins and remove the front seat cushion heater from the front seat cushion cover.
    Text in Illustration 
    *1
    Tack Pin