REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) > DISASSEMBLY |
| 1. REMOVE REAR SEAT UPPER RECLINING COVER LH |
![]() |
Using a screwdriver, detach the 3 claws and remove the cover.
| *1 | Protective Tape |
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Remove the 3 screws and handle.
| 3. REMOVE CENTER SEAT HINGE COVER RH |
![]() |
Using a clip remover, remove the clip.
Detach the 2 guides and remove the cover.
| 4. REMOVE REAR SEAT CUSHION MOULDING LH |
![]() |
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
| 5. REMOVE REAR SEATBACK LOCK STRIKER COVER LH |
![]() |
Using a clip remover, detach the 3 clips and remove the cover.
| 6. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Detach the hooks.
![]() |
Detach the hook and remove the seat cushion cover with pad.
| 7. REMOVE REAR NO. 2 SEAT PROTECTOR |
![]() |
Remove the 2 protectors from the cushion pad.
| 8. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER |
![]() |
Remove the hog rings and seat cushion cover from the seat cushion pad.
| 9. REMOVE REAR SEAT CUSHION EDGE PROTECTOR |
Remove the protector from the cushion spring.
| 10. REMOVE CENTER SEATBACK ASSEMBLY |
![]() |
Remove the 2 bolts and center seatback.
| 11. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY |
Remove the headrest.
| 12. REMOVE CENTER SEAT HINGE COVER |
![]() |
Using a clip remover, remove the clip.
Detach the 2 guides and remove the cover.
| 13. REMOVE REAR SEAT RECLINING BRACKET LH |
![]() |
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and bracket.
| 14. REMOVE REAR SEAT RECLINING BRACKET RH |
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and bracket.
| 15. REMOVE REAR SEATBACK STAY COVER LH |
![]() |
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the cover.
| 16. REMOVE REAR SEATBACK STAY COVER RH |
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the cover.
| 17. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY |
![]() |
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes.
![]() |
Remove the nut and armrest support.
![]() |
Remove the armrest as shown in the illustration.
| 18. REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY |
![]() |
Remove the 2 screws.
![]() |
Using a moulding remover, detach the 2 claws and remove the cup holder.
| 19. REMOVE REAR SEATBACK COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 20. REMOVE REAR SEATBACK LOCK COVER |
![]() |
Using a moulding remover, detach the claw.
Move the cover in the direction of the arrow to detach the clip and 2 guides, and then remove the cover.
| 21. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY |
![]() |
Using a clip remover, detach the 5 clips and remove the board.
| 22. REMOVE SEAT ARMREST COVER |
![]() |
Detach the hooks.
![]() |
Remove the cover with pad.
![]() |
Remove the cover from the pad.
| 23. REMOVE REAR SEAT HEADREST SUPPORT |
![]() |
Detach the 4 claws and remove the 2 supports.
| 24. REMOVE NO. 1 SEATBACK COVER |
![]() |
Using a moulding remover, detach the 2 claws.
![]() |
Detach the guide and remove the cover.
| 25. REMOVE REAR SEAT LOCK ASSEMBLY LH |
![]() |
Detach the clamp and disconnect the wire.
Remove the 2 bolts and lock.
| 26. REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER |
![]() |
Remove the lever as shown in the illustration.
| 27. REMOVE FOLD SEATBACK WIRE |
![]() |
Detach the 2 claws and remove the wire.
| 28. REMOVE COAT HOOK CAP |
![]() |
Using a screwdriver, detach the 2 claws and guide, and then remove the cap.
| *1 | Protective Tape |
| 29. REMOVE CENTER NO. 2 SEATBACK COVER |
![]() |
Remove the 3 screws and cover.
| 30. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
![]() |
Remove the bolt and inner belt, and disconnect the center outer belt.
| 31. REMOVE RECLINING ADJUSTER KNOB CAP LH |
![]() |
Using a screwdriver, detach the claw and guide, and then remove the cap.
| *1 | Protective Tape |
| 32. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
![]() |
Remove the 2 screws.
![]() |
Disconnect the cable in the order shown in the illustration and remove the lever.
| 33. REMOVE SEAT BELT ANCHOR COVER CAP |
![]() |
Using a screwdriver, detach the 2 claws and remove the cap.
| *1 | Protective Tape |
| 34. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Detach the 2 claws and 2 guides, and then remove the cover.
Disconnect the outer belt from the cover.
| 35. REMOVE REAR SEATBACK COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 36. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH |
![]() |
Using a clip remover, detach the 7 clips and remove the carpet.
| 37. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Detach the 4 claws and remove the 2 supports.
| 38. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the hog rings and detach the hooks, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
![]() |
Disconnect the outer belt from the seatback cover with pad.
| 39. REMOVE SEPARATE TYPE REAR SEATBACK COVER |
![]() |
Remove the hog rings and cover from the seatback pad.
| 40. REMOVE REAR SEATBACK EDGE PROTECTOR |
Remove the protector from the seatback frame.
| 41. REMOVE REAR SEAT INNER RECLINING COVER LH |
![]() |
Remove the 2 screws.
Detach the guide and remove the cover.
| 42. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the 2 screws.
Detach the 2 claws and remove the cover.
| 43. REMOVE REAR SEAT REAR CUSHION MOULDING LH |
![]() |
Using a clip remover, detach the clip.
Using a moulding remover, detach the 4 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
| 44. REMOVE CAP |
![]() |
Detach the 2 claws and remove the cap.
| 45. REMOVE REAR SEAT RECLINING COVER INNER LH |
![]() |
Detach the claw and guide, and then remove the cover.
| 46. REMOVE REAR SEATBACK SPRING DAMPER |
![]() |
Remove the 2 nuts and damper.
| 47. REMOVE REAR SEAT SHOULDER BELT GUIDE |
![]() |
Detach the claw and guide, and then remove the belt guide.
| 48. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
![]() |
Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.
| 49. REMOVE REAR SEAT RECLINING CONTROL CABLE |
Cut off the 4 cable ties.

Detach the 3 cable clamps and disconnect the cable, and then remove the cable.

| 50. REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE |
Detach the 3 cable clamps and disconnect the cable, and then remove the cable.

| 51. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH |
![]() |
Remove the 2 nuts and lever.
| 52. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH |
![]() |
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.
Remove the 2 bolts and seatback frame.
| 53. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH |
![]() |
Remove the 6 nuts and seat cushion frame.
| 54. REMOVE REAR SEAT TRACK ADJUSTING HANDLE LH |
![]() |
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the adjusting handle.