Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)

REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR SEAT TRACK ADJUSTING HANDLE LH


B237696
  1. Install the handle.

    HINT:
    Make sure the handle is straight when installing it, and check that it is centered.



2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
  1. Install the seat cushion frame with the 6 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



3. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH


B237693E01
  1. Temporarily install the seatback frame with the 2 bolts and 2 "TORX" bolts.

  1. Install the bolt to the bolt hole for the outer belt.
    Text in Illustration 
    *1
    Outer Belt Installation Bolt

  1. Using a T45 "TORX" socket wrench, tighten the 2 "TORX" bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Tighten the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Remove the bolt from the bolt hole for the outer belt.



4. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH
  1. Install the lever with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



5. INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE
  1. Install the cable to the seat frame.

  1. Attach the 3 cable clamps and connect the cable.



6. INSTALL REAR SEAT RECLINING CONTROL CABLE
  1. Install the cable to the seat frame.

  1. Attach the 3 cable clamps and connect the cable.

  1. Install 4 new cable ties.



7. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH


B241742E01

NOTICE:
When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

  1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the nut and bolt as shown in the illustration.

    HINT:
    First install the bolt, and then install the nut.

    Torque:
    for bolt:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    for nut:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Nut



8. INSTALL REAR SEAT SHOULDER BELT GUIDE
  1. Attach the guide and claw to install the belt guide.



9. INSTALL REAR SEATBACK SPRING DAMPER
  1. Install the damper with the 2 nuts.



10. INSTALL REAR SEAT RECLINING COVER INNER LH
  1. Attach the guide and claw to install the cover.



11. INSTALL CAP
  1. Attach the 2 claws to install the cap.



12. INSTALL REAR SEAT REAR CUSHION MOULDING LH


B237682
  1. Move the moulding in the direction of the arrow to attach the guide.

  1. Attach the 4 claws and clip to install the moulding.



13. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the 2 claws to install the cover.

  1. Install the 2 screws.



14. INSTALL REAR SEAT INNER RECLINING COVER LH
  1. Attach the guide and install the cover with the 2 screws.



15. INSTALL REAR SEATBACK EDGE PROTECTOR
  1. Install the protector to the seatback frame.



16. INSTALL SEPARATE TYPE REAR SEATBACK COVER


B237678E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



17. INSTALL SEATBACK COVER WITH PAD


    B237675
  1. Connect the outer belt to the seatback cover with pad.



    B237674E01
  1. Attach the hooks.
    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Hook
    *3
    Hog Ring

  1. Using hog ring pliers, install the seatback cover with pad with new hog rings.



18. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 4 claws to install the 2 supports.



19. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
  1. Attach the 7 clips to install the carpet.



20. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the cover.



21. INSTALL REAR SEAT SHOULDER BELT COVER
  1. Connect the outer belt to the cover.



    B237669
  1. Attach the 2 guides and 2 claws to install the cover.



22. INSTALL SEAT BELT ANCHOR COVER CAP


B237667
  1. Attach the 2 claws to install the cap.



23. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    B165026E02
  1. Connect the cable in the order shown in the illustration to install the lever.

  1. Install the 2 screws.



24. INSTALL RECLINING ADJUSTER KNOB CAP LH


B237664
  1. Attach the guide and claw to install the cap.



25. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH


B237670E02
  1. Install the inner belt and connect the center outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the center outer belt and inner belt to overlap the protruding parts of the seat cushion frame.

    Text in Illustration 
    *1
    Protruding Part



26. INSTALL CENTER NO. 2 SEATBACK COVER
  1. Install the cover with the 3 screws.



27. INSTALL COAT HOOK CAP


B237661
  1. Attach the guide and 2 claws to install the cap.



28. INSTALL FOLD SEATBACK WIRE
  1. Attach the 2 claws to install the wire.



29. INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER


B237658
  1. Install the lever as shown in the illustration.



30. INSTALL REAR SEAT LOCK ASSEMBLY LH
  1. Install the lock with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Attach the clamp to connect the wire.



31. INSTALL NO. 1 SEATBACK COVER


    B237655
  1. Attach the guide.



    B237653
  1. Attach the 2 claws to install the cover.



32. INSTALL REAR SEAT HEADREST SUPPORT
  1. Attach the 4 claws to install the 2 supports.



33. INSTALL SEAT ARMREST COVER


    B237649
  1. Install the cover to the pad.



    B237648
  1. Install the cover with pad.



    B237646
  1. Attach the hooks.



34. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY
  1. Attach the 5 clips to install the board.



35. INSTALL REAR SEATBACK LOCK COVER


B237643
  1. Move the cover in the direction of the arrow to attach the clip and 2 guides.

  1. Attach the claw.



36. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the cover.



37. INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY


B237640
  1. Attach the 2 claws to install the cup holder.

  1. Install the 2 screws.



38. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    B237637
  1. Install the armrest as shown in the illustration.

  1. Install the armrest support with the nut.

  1. Using a T45 "TORX" socket wrench, install the armrest and 2 bushes with the 2 "TORX" bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



39. INSTALL REAR SEATBACK STAY COVER RH
  1. Attach the guide and 3 claws to install the cover.



40. INSTALL REAR SEATBACK STAY COVER LH
  1. Attach the guide and 3 claws to install the cover.



41. INSTALL REAR SEAT RECLINING BRACKET RH
  1. Using a T45 "TORX" socket wrench, install the bracket and bush with the "TORX" bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



42. INSTALL REAR SEAT RECLINING BRACKET LH
  1. Using a T45 "TORX" socket wrench, install the bracket and bush with the "TORX" bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



43. INSTALL CENTER SEAT HINGE COVER


B237631
  1. Attach the 2 guides and install the cover with the clip.



44. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
  1. Install the headrest.



45. INSTALL CENTER SEATBACK ASSEMBLY
  1. Install the center seatback with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



46. INSTALL REAR SEAT CUSHION EDGE PROTECTOR
  1. Install the protector to the cushion spring.



47. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER


B237628E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



48. INSTALL REAR NO. 2 SEAT PROTECTOR
  1. Install the 2 protectors to the cushion pad.



49. INSTALL SEAT CUSHION COVER WITH PAD


    B237625
  1. Attach the hook.



    B237623
  1. Attach the hooks to install the seat cushion cover with pad.



50. INSTALL REAR SEATBACK LOCK STRIKER COVER LH
  1. Attach the 3 clips to install the cover.



51. INSTALL REAR SEAT CUSHION MOULDING LH


B237620
  1. Move the moulding in the direction of the arrow to attach the guide.

  1. Attach the 3 claws and clip to install the moulding.



52. INSTALL CENTER SEAT HINGE COVER RH


B237618
  1. Attach the 2 guides and install the cover with the clip.



53. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
  1. Install the handle with the 3 screws.



54. INSTALL REAR SEAT UPPER RECLINING COVER LH


B237786
  1. Attach the 3 claws to install the cover.