REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type RH Side) > DISASSEMBLY |
| 1. REMOVE REAR SEAT UPPER RECLINING COVER RH |
![]() |
Using a screwdriver, detach the 3 claws and remove the cover.
| *1 | Protective Tape |
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH |
![]() |
Remove the 3 screws and handle.
| 3. REMOVE REAR SEAT CUSHION MOULDING RH |
![]() |
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
| 4. REMOVE REAR SEAT REAR CUSHION MOULDING LH |
![]() |
Remove the screw.
Using a moulding remover, detach the 3 claws.
Detach the 2 guides and remove the moulding.
| 5. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH |
![]() |
Remove the bolt and inner belt.
| 6. REMOVE REAR SEAT INNER BELT ASSEMBLY |
![]() |
Remove the nut and inner belt.
| 7. REMOVE REAR SEATBACK LOCK STRIKER COVER RH |
![]() |
Using a clip remover, detach the 3 clips and remove the cover.
| 8. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Detach the hooks and remove the seat cushion cover with pad.
| 9. REMOVE REAR NO. 2 SEAT PROTECTOR |
![]() |
Remove the 2 protectors from the cushion pad.
| 10. REMOVE REAR SEAT CUSHION EDGE PROTECTOR |
Remove the protector from the cushion spring.
| 11. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER |
![]() |
Remove the hog 14 rings and seat cushion cover from the seat cushion pad.
| 12. REMOVE RECLINING ADJUSTER KNOB CAP RH |
![]() |
Using a screwdriver, detach the claw and guide, and then remove the cap.
| *1 | Protective Tape |
| 13. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH |
![]() |
Remove the 2 screws.
![]() |
Disconnect the cable in the order shown in the illustration and remove the lever.
| 14. REMOVE REAR SEAT COVER CAP |
![]() |
Using a screwdriver, detach the claw and guide, and then remove the cover cap.
| 15. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Remove the 2 screws.
Move the lever in the direction of the arrow to detach the guide and remove the lever.
Detach the cable clamp and disconnect the cable from the lever.
| 16. REMOVE REAR SEATBACK COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 17. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH |
![]() |
Using a clip remover, detach the 7 clips and remove the carpet.
| 18. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Detach the 4 claws and remove the 2 supports.
| 19. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the 12 hog rings and detach the hooks, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
| 20. REMOVE SEPARATE TYPE REAR SEATBACK COVER |
![]() |
Remove the 8 hog rings and cover from the seatback pad.
| 21. REMOVE REAR SEATBACK EDGE PROTECTOR |
Remove the protector from the seatback frame.
| 22. REMOVE REAR SEAT INNER RECLINING COVER RH |
![]() |
Remove the 2 screws.
Detach the guide and remove the cover.
| 23. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the 2 screws.
Detach the 2 claws and remove the cover.
| 24. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Using a clip remover, detach the clip.
Move the cover in the direction of the arrow to detach the 2 claws and remove the cover.
| 25. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Detach the claw and guide and remove the cover.
| 26. REMOVE REAR SEAT BACK SPRING DAMPER |
![]() |
Remove the 2 nuts and rear seat back spring damper.
| 27. REMOVE REAR SEAT BACK SPRING DAMPER |
![]() |
Remove the 2 nuts and rear seat back spring damper.
| 28. REMOVE REAR SEAT RECLINING CONTROL CABLE |
Cut off the 3 cable ties.

Detach the 2 cable clamps and disconnect the cable, and then remove the cable.

| 29. REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE |
Detach the cable clamp and disconnect the cable, and then remove the cable.

| 30. REMOVE REAR SEAT CUSHION SET PLATE |
![]() |
Remove the 2 nuts and set plate.
| 31. REMOVE REAR SEATBACK LOCK PLATE RH |
Detach the 2 cable clamps and disconnect the cable.
Remove the nut and lock plate.

| 32. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH |
![]() |
Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and seatback frame.
| 33. REMOVE REAR SEAT COVER |
![]() |
Remove the screw and cover.
| 34. REMOVE REAR SEAT CUSHION SPRING |
![]() |
Detach the 2 hooks and remove the spring.
| 35. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH |
![]() |
Remove the 6 nuts and seat cushion frame together with the No. 1 seat leg plate.
| *1 | No. 1 Seat Leg Plate |
| 36. REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH |
![]() |
Remove the seat cushion side frame.
![]() |
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the adjusting handle.