Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side)

REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR SEAT CUSHION LOCK STRIKER
  1. Install the striker with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



2. INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY RH


B238022E01
  1. Attach the claw and install the striker with the 2 bolts.

  1. Tighten the bolts in the order indicated in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. w/o Rear No. 2 Seat:

    1. Connect each connector.

    2. Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.

    3. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.

    4. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.

    5. Install the 3 bolts and screw.

    6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear No. 2 Seat:

    1. Connect each connector.

    2. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.

    3. Install the 3 bolts and screw.

    4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    5. Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



5. INSTALL FRONT DECK SIDE TRIM COVER RH
  1. Attach the 2 claws to install the front deck side trim cover LH.



6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
  1. Push in the No. 1 luggage compartment trim hook to install it.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim hook.



7. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
  1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



8. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)
  1. Attach the 4 claws to install the rear floor carpet assembly.



9. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
  1. Attach the 5 clips to install the rear floor mat rear support plate.



10. INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)
  1. Install the inner floor side rail sub-assembly with the 4 bolts.



11. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 2 guides to install the deck board assembly.

  1. Install the 6 bolts.



12. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)
  1. Attach the 4 clips and 2 guides to install the luggage compartment side cover sub-assembly LH.



13. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:
Use the same procedure as for the LH side.



14. INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 3 clips to install the rear No. 2 floor board assembly.



15. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)
  1. Attach the 2 clips and 2 guides to install the No. 2 deck board sub-assembly.



16. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/Deck Board, w/o Rear No. 2 Seat)
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



17. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
  1. Attach the clip to install the No. 1 deck board sub-assembly.



18. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)
  1. Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.

  1. Attach the 4 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim cover.



19. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B240010E01
  1. Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle to install the rear door opening trim weatherstrip LH as shown in the illustration.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position



20. INSTALL REAR DOOR SCUFF PLATE RH
  1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.



21. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH
  1. Attach the cable clamp to connect the cable.



    B238020
  1. Move the cover in the direction of the arrow to attach the 2 guides.

  1. Attach the 6 claws to install the lever base.



22. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
  1. Install the hinge with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



23. INSTALL REAR SEATBACK ASSEMBLY RH


B238041E01
  1. Fold down the seatback, set the seatback positioning wire on the hinge, and then temporarily install the bolt to the hinge.
    Text in Illustration 
    *1
    Positioning Wire

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Restore the seatback to the upright position and temporarily install the seatback with the 2 bolts.

  1. Tighten the bolts in the order indicated in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Attach the 2 claws and connect the outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



24. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH
  1. for Plastic Seatback Board:

    1. Attach the 4 clips to install the carpet.

    2. Attach the 5 claws and 2 clips to install the carpet.

  1. for Seatback Board with carpet:
    Attach the 2 claws and 5 clips to install the carpet.



25. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the cover.



26. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Install the headrest.



27. INSTALL REAR SEAT CUSHION ASSEMBLY RH


B240264E01
  1. Temporarily install the seat cushion with the 2 bolts.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Tighten the bolts in the order indicated in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Lock the seat cushion.



28. INSTALL REAR SEAT CUSHION HINGE COVER RH
  1. Attach the 3 claws to install the cover.



29. INSTALL REAR SEAT CUSHION HINGE COVER
  1. Attach the 3 claws to install the cover.