REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side) > DISASSEMBLY |
| 1. REMOVE REAR SEAT CUSHION |
![]() |
Remove the 2 screws and 2 cushions.
| 2. REMOVE REAR SEATBACK PROTECTOR |
![]() |
Remove the 2 screws.
Detach the 2 hooks and remove the protector.
| 3. REMOVE REAR SEAT CUSHION UNDER COVER RH |
![]() |
Using a moulding remover, detach the hooks and remove the cover.
| 4. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Disconnect the seat cushion band from the seat cushion cover.
Detach the hooks and remove the seat cushion cover with pad.
| 5. REMOVE NO. 1 SEAT CUSHION COVER RH |
![]() |
Cut off the tack pins and remove the cover from the cushion pad.
| *1 | Tack Pin |
| 6. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH |
![]() |
Remove the hog rings and seat cushion cover from the seat cushion pad.
| 7. REMOVE REAR SEAT CUSHION BAND |
![]() |
Remove the band as shown in the illustration.
| 8. REMOVE REAR SEAT LEG BRACKET COVER |
![]() |
Using a moulding remover, detach the 4 claws and remove the cover.
| 9. REMOVE REAR SEAT LEG COVER |
![]() |
Detach the claw and guide, and then remove the cover.
| 10. REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Plastic Seatback Board) |
![]() |
Using a clip remover, detach the 2 clips.
Detach the guide and remove the board.
| 11. REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Seatback Board with Carpet) |
![]() |
Using a clip remover, detach the 3 clips.
Detach the guide and remove the board.
| 12. REMOVE REAR SEAT INNER RECLINING COVER RH |
![]() |
Remove the screw.
Detach the 2 guides and remove the cover.
| 13. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY |
![]() |
Detach the fastening tape and remove the band.
Remove the bolt and inner belt.
| *1 | Band |
| 14. REMOVE CENTER SEATBACK COVER SUB-ASSEMBLY |
![]() |
Remove the screw.
Detach the 2 guides and remove the cover.
| 15. REMOVE CENTER SEATBACK ASSEMBLY |
![]() |
Using a T45 "TORX" socket wrench, remove the "TORX" bolt and bush.
Remove the 2 bolts and center seatback.
| 16. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY |
Remove the headrest.
| 17. REMOVE CENTER SEAT HINGE COVER |
![]() |
Detach the claw and remove the cover.
| 18. REMOVE REAR SEATBACK STAY COVER LH |
![]() |
Detach the 3 claws and remove the cover.
| 19. REMOVE REAR SEATBACK STAY COVER RH |
![]() |
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and hinge.
![]() |
Detach the 3 claws and remove the cover.
| 20. REMOVE REAR CENTER SEAT ARMREST ASSEMBLY |
![]() |
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts, 2 bushes and armrest.
![]() |
Remove the bush.
| 21. REMOVE NO. 2 CUP HOLDER ASSEMBLY RH |
![]() |
Remove the 2 cup holders.
| 22. REMOVE REAR SEATBACK COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 23. REMOVE REAR SEATBACK LOCK COVER |
![]() |
Using a moulding remover, detach the claw.
Move the cover in the direction of the arrow to detach the clip and 2 guides and remove the cover.
| 24. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY |
![]() |
Detach the 4 claws and 3 clips, and then remove the board.
| 25. REMOVE REAR SEAT HEADREST SUPPORT |
![]() |
Detach the 4 claws and remove the 2 supports.
| 26. REMOVE REAR NO. 1 SEAT NO. 2 SIDE PLATE |
![]() |
Remove the 2 screws.
![]() |
Using a moulding remover, detach the 3 claws and remove the plate.
| 27. REMOVE REAR SEAT LOCK ASSEMBLY RH |
![]() |
Detach the clamp and disconnect the wire.
Remove the 2 bolts and lock.
| 28. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH |
![]() |
Remove the 2 screws and control lever.
| 29. REMOVE REAR CENTER SEAT ARMREST COVER |
![]() |
Remove the screw.
Detach the 2 claws and remove the cover.
| 30. REMOVE REAR SEATBACK LOCK COVER RH |
![]() |
Remove the 2 screws.
Detach the 2 guides and remove the cover.
| 31. REMOVE REAR SEATBACK LOCK ASSEMBLY RH |
![]() |
Remove the 2 hog rings.
![]() |
Remove the 2 bolts.
While moving the release button in the direction of the arrow in the illustration, detach it from the grommet and remove the seatback lock.
| 32. REMOVE REAR SEATBACK LOCK RELEASE BUTTON |
![]() |
Remove the release button as shown in the illustration.
![]() | Counterclockwise |
| 33. REMOVE REAR SEATBACK STOP BUTTON GROMMET |
![]() |
Detach the 3 claws and remove the grommet.
| 34. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Detach the 4 claws and remove the 2 supports.
| 35. REMOVE SEAT BELT ANCHOR COVER CAP |
![]() |
Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cap.
| *1 | Protective Tape |
| 36. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Remove the screw.
Detach the 3 claws and remove the cover.
Disconnect the outer belt from the cover.
| 37. REMOVE REAR SEATBACK LOCK STRIKER PROTECTOR |
![]() |
Remove the protector from the striker.
| 38. REMOVE REAR SEAT LOCK STRIKER |
![]() |
Using a T45 "TORX" socket wrench, remove the striker.
| 39. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the hog rings, detach the hook, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
Disconnect the outer belt from the seatback cover with pad.
| 40. REMOVE SEPARATE TYPE REAR SEATBACK COVER RH |
![]() |
Remove the hog rings and cover from the seatback pad.
| 41. REMOVE REAR SEATBACK EDGE PROTECTOR |
Remove the protector from the seatback frame.
| 42. REMOVE REAR SEAT SHOULDER BELT GUIDE |
![]() |
Detach the claw and guide, and then remove the belt guide.
| 43. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.
| 44. REMOVE REAR NO. 1 SEAT PROTECTOR LH |
![]() |
Detach the 2 claws and remove the protector.
| 45. REMOVE REAR NO. 1 SEAT PROTECTOR |
![]() |
Detach the claw and remove the protector.