REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side) > REASSEMBLY |
| 1. INSTALL REAR NO. 1 SEAT PROTECTOR |
Attach the claw to install the protector.
| 2. INSTALL REAR NO. 1 SEAT PROTECTOR LH |
Attach the 2 claws to install the protector.
| 3. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH |
![]() |
Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the nut and bolt as shown in the illustration.
| *1 | Bolt |
| *2 | Nut |
| 4. INSTALL REAR SEAT SHOULDER BELT GUIDE |
Attach the guide and claw to install the belt guide.
| 5. INSTALL REAR SEATBACK EDGE PROTECTOR |
Install the protector to the seatback frame.
| 6. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH |
![]() |
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
| *1 | Hog Ring Pliers |
| 7. INSTALL SEATBACK COVER WITH PAD |
![]() |
Connect the outer belt to the seatback cover with pad.
Attach the hook.
| *1 | Hog Ring Pliers |
| *2 | Hook |
| *3 | Hog Ring |
Using hog ring pliers, install the seatback cover with pad with new hog rings.
| 8. INSTALL REAR SEAT LOCK STRIKER |
Using a T45 "TORX" socket wrench, install the striker.
| 9. INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR |
Install the protector to the striker.
| 10. INSTALL REAR SEAT SHOULDER BELT COVER |
Connect the outer belt to the cover.
Attach the 3 claws to install the cover.
Install the screw.
| 11. INSTALL SEAT BELT ANCHOR COVER CAP |
![]() |
Attach the 2 guides and 2 claws to install the cap.
| 12. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
Attach the 4 claws to install the 2 supports.
| 13. INSTALL REAR SEATBACK STOP BUTTON GROMMET |
Attach the 3 claws to install the grommet.
| 14. INSTALL REAR SEATBACK LOCK RELEASE BUTTON |
![]() |
Install the release button as shown in the illustration.
![]() | Clockwise |
| 15. INSTALL REAR SEATBACK LOCK ASSEMBLY RH |
![]() |
While moving the release button in the direction of the arrow in the illustration, attach it to the grommet.
Install the seatback lock with the 2 bolts.
![]() |
Using hog ring pliers, install 2 new hog rings.
| *1 | Hog Ring Pliers |
| 16. INSTALL REAR SEATBACK LOCK COVER RH |
![]() |
Attach the 2 hooks to install the cover.
Install the 2 screws.
| 17. INSTALL REAR CENTER SEAT ARMREST COVER |
Attach the 2 claws to install the cover.
Install the screw.
| 18. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH |
Install the control lever with the 2 screws.
| 19. INSTALL REAR SEAT LOCK ASSEMBLY RH |
Install the lock with the 2 bolts.
Attach the clamp to connect the wire.
| 20. INSTALL REAR NO. 1 SEAT NO. 2 SIDE PLATE |
![]() |
Attach the 3 claws to install the plate.
Install the 2 screws.
| 21. INSTALL REAR SEAT HEADREST SUPPORT |
Attach the 4 claws to install the 2 supports.
| 22. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY |
Attach the 4 claws and 3 clips to install the board.
| 23. INSTALL REAR SEATBACK LOCK COVER |
![]() |
Move the cover in the direction of the arrow to attach the clip and 2 guides.
Attach the claw.
| 24. INSTALL REAR SEATBACK COVER |
Attach the 4 claws to install the cover.
| 25. INSTALL NO. 2 CUP HOLDER ASSEMBLY RH |
Install the 2 cup holders.
| 26. INSTALL REAR CENTER SEAT ARMREST ASSEMBLY |
Install the bush.
Using a T45 "TORX" socket wrench, install the armrest and 2 bushes with the 2 "TORX" bolts.
| 27. INSTALL REAR SEATBACK STAY COVER RH |
Attach the 3 claws to the cover.
Using a T45 "TORX" socket wrench, install the bush and hinge with the "TORX" bolt.
| 28. INSTALL REAR SEATBACK STAY COVER LH |
Attach the 3 claws to install the cover.
| 29. INSTALL CENTER SEAT HINGE COVER |
Attach the claw to install the cover.
| 30. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
Install the headrest.
| 31. INSTALL CENTER SEATBACK ASSEMBLY |
Temporarily install the center seatback with the 2 bolts, bush and "TORX" bolt.
Tighten the 2 bolts.
Using a T45 "TORX" socket wrench, tighten the "TORX" bolt.
| 32. INSTALL CENTER SEATBACK COVER SUB-ASSEMBLY |
Attach the 2 guides and install the cover with the screw.
| 33. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY |
Install the inner belt with the bolt.
Attach the fastening tape, and install the band.
| 34. INSTALL REAR SEAT INNER RECLINING COVER RH |
Attach the 2 guides and install the cover with the screw.
| 35. INSTALL NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Plastic Seatback Board) |
Attach the guide and 2 clips to install the board.
| 36. INSTALL NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Seatback Board with Carpet) |
Attach the guide and 3 clips to install the board.
| 37. INSTALL REAR SEAT LEG COVER |
![]() |
Attach the guide and claw to install the cover.
| 38. INSTALL REAR SEAT LEG BRACKET COVER |
![]() |
Attach the 4 claws to install the cover.
| 39. INSTALL REAR SEAT CUSHION BAND |
![]() |
Install the band as shown in the illustration.
| 40. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH |
![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
| 41. INSTALL NO. 1 SEAT CUSHION COVER RH |
Install the cover to the seat cushion pad with new tack pins.
| 42. INSTALL SEAT CUSHION COVER WITH PAD |
![]() |
Attach the hooks to install the seat cushion cover with pad.
Connect the seat cushion band to the seat cushion cover.
| 43. INSTALL REAR SEAT CUSHION UNDER COVER RH |
![]() |
Attach the hooks to install the cover.
| 44. INSTALL REAR SEATBACK PROTECTOR |
Attach the 2 hooks to install the protector.
Install the 2 screws.
| 45. INSTALL REAR SEAT CUSHION |
Install the 2 cushions with the 2 screws.