FRONT CONSOLE BOX > DISASSEMBLY |
| 1. REMOVE NO. 1 POWER OUTLET SOCKET ASSEMBLY |
Disconnect the power outlet socket assembly connector.
![]() |
Using a screwdriver, detach the claw to remove the No. 1 power outlet socket assembly.
| *1 | Protective Tape |
| 2. REMOVE NO. 1 POWER OUTLET SOCKET COVER |
![]() |
Detach the 2 claws to remove the No. 1 power outlet socket cover.
| 3. REMOVE REAR CONSOLE END PANEL |
![]() |
Detach the 4 clips and 4 claws to remove the rear console end panel.
Disconnect the 2 power outlet socket assembly connectors.
| 4. REMOVE NO. 3 POWER OUTLET SOCKET ASSEMBLY |
Detach the connector clamp.
![]() |
While pulling the claw of the No. 3 power outlet socket assembly in the direction of the arrow, push the No. 3 power outlet socket assembly toward the inside of the chamber to remove it.
| 5. REMOVE CENTER POWER OUTLET SOCKET COVER |
![]() |
Detach the 2 claws to remove the center power outlet socket cover.
| 6. REMOVE CONSOLE BOX REGISTER ASSEMBLY |
![]() |
Detach the 4 claws to remove the console box register assembly.
| 7. REMOVE CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY |
![]() |
Remove the 6 screws and console compartment door sub-assembly.
| 8. REMOVE CONSOLE COMPARTMENT DOOR LOCK SUB-ASSEMBLY |
![]() |
Remove the 2 screws and console compartment door lock sub-assembly.
| 9. REMOVE CONSOLE COMPARTMENT DOOR HINGE SUB-ASSEMBLY |
![]() |
Remove the 4 screws.
Using a screwdriver, detach the 6 claws to remove the console compartment inner door.
| *1 | Protective Tape |
![]() |
Remove the 4 screws and console compartment door hinge sub-assembly.
| 10. REMOVE CONSOLE CUP HOLDER BOX |
![]() |
Remove the 6 screws and console cup holder box.
| 11. REMOVE BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY |
![]() |
Detach the 2 claws and remove the regulator switch.
| 12. REMOVE SEAT HEATER SWITCH (w/ Seat Heater System) |
![]() |
Disconnect the 2 connectors.
![]() |
Detach the 4 claws and remove the 2 switches.
| 13. REMOVE SWITCH BASE |
![]() |
Remove the 2 screws and switch base.
| 14. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for VF2A) |
![]() |
Detach the 6 claws to remove the shifting hole cover sub-assembly.
| 15. REMOVE FRONT UPPER CONSOLE PANEL GARNISH |
for VF2A:
![]() |
Detach the 6 claws to remove the front upper console panel garnish.
| *A | for VF2A |
for 2WD, for VF2BM, VF4BM:
Detach the 10 claws to remove the front upper console panel garnish.

| *A | for 2WD | *B | for VF2BM, VF4BM |
| 16. REMOVE NO. 2 BOX BOTTOM MAT (for 2WD) |
![]() |
Detach the 4 claws to remove the No. 2 box bottom mat.
| 17. REMOVE TRANSFER POSITION SWITCH (for VF2BM) |
![]() |
Detach the 3 claws and remove the transfer position switch.
| 18. REMOVE TRANSFER POSITION SWITCH (for VF4BM) |
![]() |
Detach the 3 claws and remove the transfer position switch.