Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (w/ Intuitive Parking Assist System)

FRONT BUMPER (w/ Intuitive Parking Assist System) > DISASSEMBLY

for Preparation Click here



1. REMOVE RADIATOR GRILLE


    B354485E01
  1. Put protective tape around the radiator grille.
    Text in Illustration 
    *1
    Protective Tape



    B354484
  1. Detach the 10 claws and 2 guides to remove the radiator grille.



2. REMOVE NO. 2 ENGINE ROOM WIRE
  1. Disconnect each connector.



  1. Detach the 9 clamps to remove the No. 2 engine room wire.


    B353487



3. REMOVE NO. 1 ULTRASONIC SENSOR


    E201175
  1. Detach the 2 claws to remove the No. 1 ultrasonic sensor from the No. 2 ultrasonic sensor retainer.

    HINT:
    Use the same procedure as for the other side.



4. REMOVE ULTRASONIC SENSOR CLIP


    B352864E01
  1. Using a screwdriver, detach the claw to remove the ultrasonic sensor clip from the No. 1 ultrasonic sensor as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER


    E203373
  1. Detach the 3 claws to remove the No. 2 ultrasonic sensor retainer from the front bumper cover.

    HINT:
    Use the same procedure as for the other side.



6. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ License Plate Bracket)


    B353215
  1. Remove the 2 screws and front bumper extension mounting bracket.



7. REMOVE FRONT BUMPER SIDE MOULDING LH


    B353216
  1. Remove the 2 outside moulding retainers.

  1. Detach the claw to remove the front bumper side moulding LH.



8. REMOVE FRONT BUMPER SIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE FRONT BUMPER LOWER SIDE SUPPORT LH


    B354462
  1. Remove the 2 clips.

  1. Detach the 5 claws to remove the front bumper lower side support LH.



10. REMOVE FRONT BUMPER LOWER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



11. REMOVE NO. 2 RADIATOR GRILLE MOULDING


    B360820
  1. Remove the 2 outside moulding retainers and 4 screws.



    B353217
  1. Detach the 4 claws to remove the No. 2 radiator grille moulding.



12. REMOVE FRONT BUMPER SIDE MOULDING SUB-ASSEMBLY LH


    B353219
  1. Remove the 3 outside moulding retainers.

  1. Remove the 2 screws.

  1. Detach the 2 claws and guide to remove the front bumper side moulding sub-assembly LH.



13. REMOVE FRONT BUMPER SIDE MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



14. REMOVE FRONT BUMPER MOULDING SUB-ASSEMBLY


    B353218
  1. Remove the 4 screws.



    B354487
  1. Remove the 15 outside moulding retainers.



    B357463
  1. Detach the 12 guides and 4 claws to remove the front bumper moulding sub-assembly.



15. REMOVE FOG LIGHT ASSEMBLY LH


    E280416
  1. Remove the 2 screws.

  1. Detach the 2 guides to remove the fog light assembly LH.



16. REMOVE FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.