Home › Drivetrain · AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM

DIFFERENTIAL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK 4WD CONTROL ECU

C159461E08

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F47-6 (RLY1) - F46-4 (GND)
    G - W-B
    Rear differential lock actuator limit switch
    Ignition switch ON
    Rear differential lock actuator limit switch on
    Below 1.5 V
    Ignition switch ON
    Rear differential lock actuator limit switch off
    11 to 14 V
    F47-7 (RLY2) - F46-4 (GND)
    P - W-B
    Rear differential lock actuator limit switch
    Ignition switch ON
    Rear differential lock actuator limit switch on
    Below 1.5 V
    Ignition switch ON
    Rear differential lock actuator limit switch off
    11 to 14 V
    F47-11 (R) - F46-4 (GND)
    SB - W-B
    Rear differential lock switch
    Ignition switch ON
    Rear differential lock switch on
    Below 1.5 V
    Ignition switch ON
    Rear differential lock switch off
    11 to 14 V
    F47-14 (RLP) - F46-4 (GND)
    V - W-B
    Rear differential lock detection switch
    Ignition switch ON
    Rear differential lock detection switch on
    Below 1.5 V
    Ignition switch ON
    Rear differential lock detection switch off
    9.5 to 14 V
    F46-8 (M1) - F46-4 (GND)
    LG - W-B
    Differential lock actuator motor
    Ignition switch ON
    Differential lock switch off → on (Differential lock switch OFF → ON (For 5 seconds after power supplied or until switching of limit switch is complete during FREE to LOCK switching))
    11 to 14 V
    Ignition switch ON
    Differential lock switch off → on (Differential lock actuator motor stopped)
    Below 1.5 V
    F46-3 (IG) - F46-4 (GND)
    R - W-B
    IG power
    Ignition switch ON
    11 to 14 V
    F46-4 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F46-7 (M2) - F46-4 (GND)
    L - W-B
    Differential lock actuator motor
    Ignition switch ON
    Differential lock switch on → off (Differential lock switch ON → OFF (For 5 seconds after power supplied or until switching of limit switch is complete during LOCK to FREE switching))
    11 to 14 V
    Ignition switch ON
    Differential lock switch on → off (Differential lock actuator motor stopped)
    Below 1.5 V
    F47-19 (CANH) - F46-4 (GND)
    G - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation (see waveform 1)
    F47-20 (CANL) - F46-4 (GND)
    W - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation (see waveform 2)



  2. A086154E52
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbols)
    F47-19 (CANH) - F46-4 (GND)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON
    Text in Illustration 
    *1
    Waveform 1

    HINT:
    The waveform varies depending on the CAN communication signal.



  4. A086155E49
  5. Using an oscilloscope, check waveform 1.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbols)
    F47-20 (CANL) - F46-4 (GND)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON
    Text in Illustration 
    *1
    Waveform 2

    HINT:
    The waveform varies depending on the CAN communication signal.