ENTRY AND START SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The main components of the start function have the following functions:
| Component | Function |
Push Start Switch
|
|
| Key | Receives signals from the antennas and returns the ID code to the door control receiver. |
| Indoor Electrical Key Oscillator | The indoor electrical key oscillator and the No. 2 indoor electrical key oscillator transmits a request signal from the smart key ECU assembly and form an actuation area inside the vehicle interior. |
| Door Control Receiver | Receives the ID code from the key and transmits it to the smart key ECU assembly. |
| Smart Key ECU Assembly |
|
| Stop Light Switch Assembly*1 | Outputs the state of the brake pedal to the smart key ECU assembly. |
| Clutch Start Switch Assembly*2 | Outputs the state of the clutch pedal to the smart key ECU assembly and ECM. |
| Immobiliser Code ECU*3 | Receives the steering unlock or engine immobiliser unset request signal from the smart key ECU assembly, certifies it, and transmits each unset signal to the steering lock ECU and ECM. |
| ECM |
|
Steering Lock Actuator Assembly
| The steering wheel locks and unlocks according to signals from the smart key ECU assembly. |
| Park/Neutral Position Switch Assembly*1 | Outputs the shift lever position signal to the smart key ECU assembly. |
The main components of the entry function have the following functions:
| Component | Function | |
| Key |
| |
| Smart Key ECU Assembly |
| |
| Main Body ECU (Network Gateway ECU) |
| |
| Door Handle Assembly | Touch Sensor | Transmits the door unlock request signal to the smart key ECU assembly. |
| Lock Sensor | Transmits the door lock request signal to the smart key ECU assembly. | |
| Door Electrical Key Oscillator | Transmits the request signal from the smart key ECU assembly, and forms an actuation area around the driver's and the front passenger's doors. | |
| Indoor Electrical Key Oscillator | Transmits the request signal from the smart key ECU assembly, and forms an actuation area inside the interior of the vehicle and the interior of the luggage compartment. | |
| Electrical Key Antenna | Transmits the request signal from the smart key ECU assembly, and forms an actuation area around the luggage compartment. | |
| Door Control Receiver | Receives the ID code from the key in the actuation area and transmits it to the smart key ECU assembly. | |
| Back Door Opener Switch | Transmits a luggage door open request signal to the smart key ECU assembly. | |
| Wireless Door Lock Buzzer | When the smart key ECU assembly detects human errors, it warns the driver by sounding the wireless door lock buzzer*2, illuminating the master warning light, and sounding the buzzer in the combination meter assembly in accordance with the request signal from the smart key ECU assembly. | |
| Combination Meter Assembly | Buzzer | |
| Master Warning Light | ||
| OPERATING CONDITION |
The special functions of the entry and start system only work when the key is in the actuation area formed by the 5 oscillators and the antenna.
The indoor electrical key oscillator and No. 2 indoor electrical key oscillator form the actuation area of the start function.
The door electrical key oscillators and the electrical key antenna form the actuation area of the entry function.

| Actuation Area | Details |
| Interior | The interior actuation area of the indoor electrical key oscillators is formed when the door is opened or closed, when the push start switch is pressed, when the brake pedal is depressed*1, when the clutch pedal is depressed*2, when a warning is activated. |
| Exterior | The exterior actuation area formed by the door electrical key oscillators and electrical key antenna is approx. 0.4 m to 0.8 m (15.7 in. to 31.5 in.) from the outside door handle of the front doors, or the center of the rear bumper. |
| Front Door Area | The exterior actuation area of the door electrical key oscillators is formed by transmitting a request signal every 0.25 seconds while the push start switch is off and each door is locked. In this way the proximity of a key can be detected. When locking the door using the lock sensor on the outside door handle, the actuation area is formed when the lock sensor is touched. |
| Luggage Compartment Door Area | The exterior actuation area of the electrical key antenna is formed when the back door opener switch is on. |
| FUNCTION |
Start Function
The start function has different power source modes to suit the brake pedal condition and shift lever position*1 or clutch pedal condition*2.
When a driver who is carrying a key enters the vehicle while the power source mode is off, and presses the push start switch without depressing the brake pedal*1 or the clutch pedal*2, the power source mode turns on (ACC). With each pressing of the push start switch, the power source mode switches as follows: off → on (ACC) → on (IG) → off.
When a driver who is carrying a key enters the vehicle while the power source mode is off, and depresses the clutch pedal*2 or depresses the brake pedal while the shift lever is in P or N*1. Pressing the push start switch will cause the engine to start.
When starting the engine with the vehicle stopped, pressing the push start switch while the shift lever is in P will cause the power source mode to turn off. Pressing the push start switch when the shift lever is in any position other than P will cause the mode to turn on (ACC).*1
When starting the engine with the vehicle stopped, pressing the push start switch will cause the power source mode to turn off.*2


Transition of the power source mode when the key battery is low or the key is not operating normally due to an electromagnetic interference:
Starting the engine when the key battery is low or the key is not operating normally due to an electromagnetic interference:
Entry Function
The entry function consists of the following functions:
| Function | Outline |
| Wireless Door Lock Control | This function is a convenient system for locking and unlocking all the doors and unlocking the luggage door from a distance. The operation of this function in the entry and start system is the same as that of the wireless door lock control system. However, the receiver in the smart key ECU assembly uses a door control receiver to perform the control. |
| Entry Illumination | When a key enters any actuation area of the door electrical key oscillator, the map light and push start switch illumination light illuminate. |
| Entry Unlock | When a key is located in the exterior actuation area of a door electrical key oscillator, touching any touch sensor will cause doors to unlock.
|
| Entry Lock | When a key is located in the exterior actuation area of any door electrical key oscillator or electrical key antenna and the push start switch is off, all doors can be locked by simply touching the lock sensor or pressing the lock switch. |
| Entry Luggage Door Open | When a key is in an exterior actuation area of the electrical key antenna, the luggage door can be opened manually by simply pressing the back door opener switch. |
| Prevention of Key Confinement |
|
| Key Cancel | The following key functions can be canceled by following certain procedures:
|
| Battery Saving | To prevent the key battery and the vehicle battery from becoming discharged, the battery saving function activates when the vehicle remains unused for a long period of time. |
| Warning | The entry and start system causes the smart key ECU assembly to sound the buzzer in the combination meter assembly and wireless door lock buzzer*5 in order to alert the driver. |
| Key Code Registration Function | A total of 7 keys can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the smart key ECU assembly. |
Wireless Door Lock Control Function
The wireless door lock control function has the following functions:
| Function | Outline | Customized Body Electronics System*1 |
| All Doors Lock | Pressing the lock button of the key locks all doors. | Default Setting is on. |
| All Doors Unlock |
| Default Setting is on. |
| Luggage Door Open | Pressing the luggage door open button of the key opens the luggage door. | Default Setting is on. |
| Answer Back |
| Default Setting is on. |
| Automatic Lock | If none of the doors are opened within 30 seconds*3 (60 seconds)*5 after they have been unlocked by the wireless door lock control, all the doors will be locked again automatically. The starting time of the automatic lock function can be changed to 120, 60, or 30 seconds. | Standard*2 |
| Door Ajar Warning*7 | If any door is open or ajar, pressing the lock button of the key will cause the wireless door lock buzzer to sound for about 10 seconds. | Default Setting is on. |
Entry Unlock Function
When a key is located in the exterior actuation area of any door electrical key oscillator, touching the touch sensor of an outside door handle will cause doors to unlock.
After the doors are unlocked, the hazard lights will flash twice as an answer back, and the wireless door lock buzzer*3 will sound twice.

| *1 | Touch Sensor | - | - |
Entry Lock Function
When all doors are closed and a key is located in the exterior actuation area of any door electrical key oscillator, all doors can be locked through the following operations: touching the lock sensor of an outside door handle.
After the doors are locked, the hazard lights will flash once as an answer back, and the wireless door lock buzzer* will sound once.

| *1 | Lock Sensor | - | - |
Entry Luggage Door Unlock Function
When a key is located in the exterior actuation area of the electrical key antenna, pressing the back door opener switch will cause the luggage door to unlock.
Warning Function
When any of the situations below occur, the entry and start system causes the smart key ECU assembly to illuminating the master warning light, sound a buzzer in the combination meter assembly and sound the wireless door lock buzzer*1 in order to alert the driver.
| Situation | Condition |
| A*2 | The shift lever is in any position other than P and the power source mode is anything other than off. |
| B | The driver door is opened while the steering is unlocked. |
| C | The shift lever is in P*2 and the power source mode is anything other than off. |
| D | The occupant leaves with the key. |
| E | The push start switch is operated while the key is outside the actuation area. |
| F | The entry lock is operated while the key is inside the vehicle. |
| G | The entry lock is operated while any of the doors are open. |
| H | The luggage door is closed while the key is inside the luggage compartment. |
| I*3 | Because the key is confined inside the vehicle interior, the stop-confinement door unlock function will activate. |
| J | The key battery is low. |
| K | The steering lock cannot be released. |
| L | A steering lock ECU malfunction has been detected. |
| M*3 | An engine start method is displayed. |
| N | The key and engine switch ID codes have been authenticated. |
| O | The vehicle is driven without the key. |
| P*4 | A clutch start switch assembly malfunction has been detected. |
There are two patterns for situation A (models with A/T)
| Possible Effects without Warning | Sudden vehicle start, vehicle theft, vehicle roll-away | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Continuously sounds |
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effects without Warning | Sudden vehicle start, vehicle theft, vehicle roll-away | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Continuously sounds |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Continuously sounds* | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation B
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when one of the following conditions is met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Intermittently sounds |
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
There are two patterns for situation C
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds 3 times*2 | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Continuously sounds*2 | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation D
| Possible Effects without Warning | Engine cannot be restarted. | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | Sounds 3 times* | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation E
| Possible Effects without Warning | Driver confusion | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation F
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | Continuously sounds* | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation G
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | Continuously sounds* | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation H
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | Continuously sounds* | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation I (models for Europe [RHD])
| Possible Effects without Warning | Vehicle theft | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | - | ||
| Wireless Door Lock Buzzer | Continuously sounds | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation J
| Possible Effects without Warning | Entry and start system does not function. | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| |||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation K
| Possible Effects without Warning | Entry and start system does not function. | ||
| Warning Condition | The steering lock does not release when performing the release operation, preventing the engine from starting. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation L
| Possible Effects without Warning | Malfunction detection | ||
| Warning Condition | The smart key ECU assembly gives a warning when one of the following conditions is met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation M (models for Europe [RHD])
| Possible Effects without Warning | Usability function | ||
| Prerequisite |
| ||
| Warning Condition | Push start switch is pushed. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation N
| Possible Effects without Warning | Usability function | ||
| Warning Condition | ID code certification is completed. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | - | ||
In situation O
| Possible Effects without Warning | Restarting prevention | ||
| Warning Condition | The smart key ECU assembly gives a warning when all the following conditions are satisfied:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Intermittently sounds |
| Master Warning Light | Blinks | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
In situation P (models with M/T)
| Possible Effects without Warning | Malfunction detection | ||
| Prerequisite |
| ||
| Warning Condition | Driver door is changed from closed to open. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Master Warning Light | Blinks | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Battery Saving Function
Vehicle Battery Saving
Key Battery Saving
Key Cancel Function
A key cancel function is provided to make it possible to disable the entry and start system. Key cancel can be operated when certain operations are performed when the vehicle is in the following conditions:
Key Code Registration Function
The table below shows the 4 special ID code registration function modes through which up to 7 different codes can be registered. The codes are electronically registered (written and stored) in the EEPROM. For details of the recognition code registration procedure, refer to the Service Bulletin.
| Mode | Function |
| Rewrite | Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or an integration relay is replaced. |
| Add | Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. |
| Confirm | Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist. |
| Prohibit | Clears all registered codes. This mode is used when a key is lost. |
| CONSTRUCTION |
Key
The key consists of a mechanical key, a transmitter for the wireless door lock control and a transceiver for the entry and start system.
The transceiver for the entry and start system receives the signals from the oscillators and returns the ID code to the door control receiver.
The transmitter for the wireless door lock control has a lock button, unlock button, luggage door open button and panic alarm button*.
When the key battery is low, the radio wave response received from the push start switch is returned to the push start switch by the key.
This mechanical key works for the driver door, but cannot be used to start the engine.

| *A | Except Models for China | *B | Models for Korea |
| *1 | Lock Button | *2 | Unlock Button |
| *3 | Luggage Door Open Button | *4 | Panic Alarm Button |
| *5 | Mechanical Key | - | - |

| *A | Models for China | - | - |
| *1 | Lock Button | *2 | Luggage Door Open Button |
| *3 | Unlock Button | *4 | Mechanical Key |
Push Start Switch
The push start switch consists LEDs and a transponder key amplifier.
The LEDs are used for the illumination light.
Smart Key ECU Assembly
The smart key ECU assembly consists of the IG1 and IG2 relay actuation circuits, a CPU, and a hold circuit.
The hold circuit is installed to prevent the power supply to the relays from being cut off when an abnormality occurs in the IG1 and/or IG2 relay actuation circuits during driving.

| DIAGNOSIS |
The smart key ECU assembly can detect malfunctions in the start function when the power source mode is on (IG). At the same time, the ECU stores the 5-digit DTC in the memory.
The DTC can be read by connecting a Grobal TechStream (GTS) to the DLC3.
The start function cannot be operated again if a malfunction occurs.
For details, refer to the corresponding Repair Manual for this model.