MANUAL TRANSMISSION SYSTEM > DETAILS



CONSTRUCTION


  1. Gear Train



    1. The transmission synchromesh mechanism is an all-speed constant mesh type.

      Gear
      1st, 2nd and 3rd
      4th, 5th, 6th and Reverse
      Synchromesh mechanism type
      Triple-cone
      Single-cone


      X108369E01


      Text in Illustration 
      *1
      Input Shaft
      *2
      Reverse Gear
      *3
      4th Gear
      *4
      3rd Gear
      *5
      2nd Gear
      *6
      1st Gear
      *7
      6th Gear
      *8
      5th Gear
      *9
      Triple-cone Type Synchromesh Mechanism
      *10
      Counter Shaft
      *11
      Output Shaft
      -
      -



  2. Shift Control Mechanism

    1. The shift control mechanism uses the semi-direct method to achieve short stroke and good rigidity.

    2. Friction is lowered during operation by the adoption of slide ball bearings in the shift fork shaft support part, improving the feel of shifting while driving as well as when at a standstill.



    3. Resin or leather gearshift lever knob is available according to specifications.


      X108766E01


      Text in Illustration 
      *1
      Shift Lever Knob
      *2
      Manual Transmission Assembly
      *a
      Semi-Direct Mechanism
      -
      -

    4. The reverse miss shift prevention mechanism prevents shifting into reverse unless the shift lock release collar provided on the shift lever is raised.



    5. A pull-collar gearshift lever has been adopted to prevent incorrect operation while in forward or in reverse.


      X108368E01


      Text in Illustration 
      *1
      Pull Collar
      -
      -
      *a
      Shift Pattern
      -
      -



    6. A stopper cover is provided on the 1st-2nd side, so that the pull collar must be pulled upward in order to shift into reverse. This reduces the amount of shift effort and ensures a precise shifting operation.


      X108767E01


      Text in Illustration 
      *1
      Stopper Cover
      *2
      Pull Collar
      *a
      Neutral
      *b
      1st/2nd
      *c
      Reverse
      -
      -
      V100135
      Select Direction
      V100136
      Pulled-Up



  3. Shift and select mechanism

    1. The shift mechanism has 4 shift forks, 5 shift fork shafts, and an interblock.



    2. Friction is lowered during operation by the adoption of slide ball bearings in the shift fork shaft support part, improving the feel of shifting while driving as well as when at a standstill.


      X108370E01


      Text in Illustration 
      *1
      Interlock Block
      *2
      1st-2nd Shift Fork
      *3
      5th Reverse Shift Fork
      *4
      Main Shift Fork Shaft
      *5
      No. 2 Shift Fork Shaft
      *6
      No. 3 Shift Fork Shaft
      *7
      3rd-4th Shift Fork
      *8
      6th Shift Fork
      *9
      No. 5 Shift Fork Shaft
      *10
      No. 4 Shift Fork Shaft



    3. Friction is lowered during operation by the adoption of slide ball bearings in the shift fork shaft support part.


      X108774E01


      Text in Illustration 
      *1
      Shift Fork Shaft
      *2
      Slide Ball Bearing
      *a
      Shift Fork Shaft Support Part
      -
      -



    4. All shift forks in the shift fork shaft slide mechanism are fastened to the shift fork shaft, and a system whereby the entire fork shaft slides has been adopted, reducing friction during operation.


      X108775E01


      Text in Illustration 
      *1
      Shift Fork Shaft
      *2
      Shift Fork
      *a
      The entire fork shaft slides smoothly.
      -
      -
      V100135
      Slide
      -
      -



    5. A ball plunger shift detent has been adopted for the shift detent mechanism, and a non-linear cam that enables quick select operation through negative slope characteristics and by clarifying the neutral gear position has been adopted.


      X108776E01