METER / GAUGE SYSTEM > DETAILS



FUNCTION
  1. Except Models with TFT LCD Type Multi-information Display

    1. Buzzer Function

      1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

        Priority
        Item
        1
        Speed Limiter Warning*1
        2
        Front Seat Belt Warning
        3
        EPS Warning
        4
        Key Reminder
        5
        Hill Start Assist Control Warning
        6
        Engine Immobiliser Matching Completion Report
        7
        Shift Operation Reject Warning*2
        8
        Rev/Red Zone Warning*3
        9
        Light Reminder

        HINT:
        *1: Models for G.C.C. countries
        *2: Models with A/T
        *3: Models with rev indicator/red zone indicator

    2. Multi-information Display Function

      Display
      Display Item
      Outline
      Y120434
      Odometer Display
      Displays the odometer.
      Y120435
      Trip Meter A Display
      Displays the trip meter A.
      Y120436
      Trip Meter B Display
      Displays the trip meter B.
      Y120437
      M/T Shift and Shift-up Indicator Customize Display*1
      (While IG OFF)
      1. Displays whether M/T shift and shift-up indicator display control is off or on.
      2. When the ignition is off and the trip meter B is being displayed, pressing the ODO/TRIP switch quickly changes the display mode to M/T shift and shift-up indicator customize. Holding the ODO/TRIP switch down can toggle it between off and on.
      3. Initial setup is off.
      Y120438
      Outside Temperature Display
      Displays the temperature outside.*2
      Y120439
      Instant Fuel Consumption Display
      1. Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.
      2. The display updates constantly.
      Y120440
      Average Fuel Consumption After Refueling Display
      1. Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after reset and the fuel consumption.
      2. Holding down the DISP switch will reset the fuel consumption meter.
      3. The display updates every 10 seconds.
      Y120441
      Rev Indicator/Red Zone Indicator Customize Display*3
      (While a Vehicle Stop)
      1. Displays the starting engine revolution count for rev indicator light-up.
      2. While rev indicator/red zone indicator customize is indicated, holding down the DISP switch changes it to setup mode. The starting engine revolution count for rev indicator light-up (2000 to 7400 revolutions) and rev/red zone buzzer on/off can be set.
      3. When setting the rev indicator, the rev indicator will light up and the tachometer will display the set engine revolution count for 1 second with the ignition on.
      4. The initial setup is the function off state.

      HINT:
      *1: Models with M/T shift and shift-up indicator customize display function for M/T
      *2: The indication of the outside temperature is influenced by vehicle speed, and the indication during a stop (low vehicle speed) is not updated, but is not abnormal.
      *3: Models with rev indicator/red zone indicator

  2. Models with TFT LCD Type Multi-information Display

    1. Buzzer Function

      1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

        Priority
        Item
        1
        Speed Limiter Warning*1
        2
        Front Seat Belt Warning
        3
        EPS Warning
        4
        Entry and Start System Warning
        5
        Hill Start Assist Control Warning
        6
        Multi-information Display Warning
        7
        Engine Immobiliser Matching Completion Report
        8
        Shift Operation Reject Warning*2
        9
        Rev/Red Zone Warning
        10
        Light Reminder

        HINT:
        *1: Models for G.C.C. countries
        *2: Models with A/T

    2. Setting Function

      1. The items displayed on the multi-information display can be customized.
      2. The items can be selected on the information setting screen.

        Item
        Available Setting
        Initial Performance
        The videos display on the multi-information display can be switched:
        1. ON (Default)
        2. OFF

        HINT:
        1. One of three opening videos is played at random each time the ignition is switched on.
        2. One of three ending videos is played at random each time the ignition is switched off.

        REV Indicator
        1. The rev indicator setting on the multi-information display can be adjusted:

        HINT:
        The engine speed for rev indicator activation can be set at increments of 100 rpm between 2000 rpm and 7400 rpm.

        1. The rev zone warning buzzer can be switched:
          1. ON
          2. OFF (Default)
        GSI Customize*
        The GSI (Gear Shift Indicator) customize setting on the multi-information display can be switched:
        Language
        The language used on the multi-information display can be selected:
        1. English
        2. French
        3. Spanish
        4. German
        5. Italian
        6. Russian
        7. Chinese
        8. Turkish

        HINT:
        The selectable language may differ depending on the model or region.

        Unit
        The unit displayed on the multi-information display can be selected:
        1. miles (MPG (US))
        2. miles (MPG (Imperial))
        3. km (L/100 km)
        4. km (km/L)

        HINT:
        The selectable units may differ depending on the model.

        Initialization
        The setting items on the multi-information display can be in initialized.

        HINT:
        *: Shown or hidden according to the destination.

    3. Warning Mode Function

      1. When a warning is necessary, the warning display interrupts the display in the multi-information display.
      2. The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.

        Priority
        Display
        Master Warning light
        Buzzer
        1
        Brake Malfunction
        Illuminates
        Sounds
        2
        Door Open (While Driving)
        Blinks
        -
        3
        Door Open
        -
        -
        4
        Auto Power Off to Conserve Battery
        -
        -
        5
        Shift to P position when parked
        Blinks
        Sounds
        6
        Check Power Steering System
        Illuminates
        Sounds
        7
        Key not detected
        Blinks
        Sounds
        8
        Check SRS Airbag System
        Illuminates
        Sounds
        9
        Check ABS
        -
        Sounds
        10
        Engine Coolant High Temperature
        Illuminates
        Sounds
        11
        Check Access System with Elec. Key
        Blinks
        Sounds
        12
        Transmission Fluid High Temperature
        Illuminates
        Sounds
        13
        Turn Power Off
        Blinks
        Sounds
        14
        Key detected in vehicle
        Blinks
        Sounds
        15
        Turn Light Off
        Blinks
        Sounds
        16
        Depress brake pedal, touch engine switch with key
        Blinks
        Sounds
        17
        Depress clutch pedal, touch engine switch with key
        Blinks
        Sounds
        18
        Depress brake pedal and push engine switch to start
        Blinks
        Sounds
        19
        Depress clutch pedal and push engine switch to start
        Blinks
        Sounds
        20
        Shift to P position to Start
        Blinks
        Sounds
        21
        Steering Lock active
        Blinks
        Sounds
        22
        Key Battery Low
        Illuminates
        Sounds
        23
        Fuel Low
        -
        -
        24
        Roads may be icy
        -
        -
        25
        No Messages
        -
        -


OPERATION
  1. Except Models with TFT LCD Type Multi-information Display

    1. Switching the Multi-information Display


      1. The multi-information display changes in the order shown below by pressing the ODO/TRIP switch or DISP switch.


        Y120443E02


        Text in Illustration 
        *A
        Models with M/T Shift and Shift-up Indicator Customize Display Function for M/T
        -
        -
        *1
        ODO/TRIP Switch
        *2
        DISP Switch
        *3
        Odometer Display
        *4
        Trip Meter A Display
        *5
        Trip Meter B Display
        *6
        M/T Shift and Shift-up Indicator Customize Display: G-On (While IG OFF)
        *7
        M/T Shift and Shift-up Indicator Customize Display: G- Off (While IG OFF)
        *8
        Outside Temperature Display
        *9
        Instant Fuel Consumption Display
        *10
        Average Fuel Consumption After Refueling Display
        *11
        Rev Indicator/Red Zone Indicator Customize Display (Models with Rev Indicator/Red Zone Indicator) (While a Vehicle Stop)
        *12
        Rev Indicator/Red Zone Indicator Customize Display Setup Mode (Models with Rev Indicator/Red Zone Indicator) (While a Vehicle Stop)
        *a
        ODO/TRIP switch short press
        *b
        ODO/TRIP switch long press
        *c
        DISP switch short press
        *d
        DISP switch long press

    2. Rev Indicator/Red Zone Indicator Customize Setup Mode Display

      1. The starting engine revolution count for rev indicator light-up (2000 to 7400 revolutions) and rev/red zone buzzer on/off can be set.

      2. When average fuel consumption is indicated while the vehicle is stopped, pressing the DISP switch quickly displays the rev indicator/red zone indicator customize mode. Holding down the DISP switch changes it to setup mode.


        Y120445E01


        *A
        Rev Indicator Revolution Count Setup Mode
        *B
        Rev/Red Zone Buzzer On/Off Setup Mode
        *C
        Thousands-Digit Setup Screen
        *D
        Hundreds-Digit Setup Screen
        *E
        Revolution Count Confirmation Screen
        *F
        Buzzer On/Off Setup Screen
        *G
        Buzzer Setup Confirmation Screen
        -
        -
        *1
        Rev Indicator/Red Zone Indicator Customize Display
        -
        -
        *a
        Initial display. Displays previous revolution setting if a previous setting value exists.
        *b
        "REV." and setable area blink during setup mode.
        *c
        Switch input invalid (1 second indication)
        -
        -
        V100135
        DISP switch short press
        V100136
        DISP switch long press
        →
        Automatic transition
        []
        Setting value

  2. Models with TFT LCD Type Multi-information Display

    1. Switching the Multi-information Display

      1. Display Function Flow

        1. The multi-information display flow can be switched as shown in the flow chart below:


          Y199119E01


          Item
          Display Change Condition
          (1)
          Conditions are met.
          (2)
          Conditions are not met.
          (3)
          If there are multiple display requests, items will be displayed in sequence.
          (4)
          Item or display is selected by operating the steering pad switch assembly switch.
          (5)
          ODO and remaining fuel display is displayed for a certain period of time after the ignition switch is turned off and the ODO/TRIP switch is pressed.
      2. Display Tab Operation

        1. The information currently displayed can be switched using the RIGHT/LEFT switch on the steering pad switch assembly.


          Y199109E01


          Text in Illustration 
          *1
          Steering Pad Switch Assembly
          -
          -
          *a
          LEFT Switch
          *b
          RIGHT Switch
          *c
          Drive Information
          *d
          Driving Assist System Information
          *e
          Setting
          *f
          Message
          *g
          The illustrations shown are examples only.
          -
          -
          V100135
          Pressing the LEFT switch
          V100136
          Pressing the RIGHT switch

        2. The information currently displayed can be switched using the UP/DOWN switch and BACK switch on the steering pad switch assembly.


          Y199129E01


          Text in Illustration 
          *1
          Steering Pad Switch Assembly
          -
          -
          *a
          UP Switch
          *b
          BACK Switch
          *c
          DOWN Switch
          -
          -

          Information Tab 
          Tab
          Display
          Drive information
          Drive information 1
          1. Instantaneous fuel consumption
          2. Average fuel consumption
          3. Cruising distance
          Drive information 2
          1. Average vehicle speed
          2. Continuous operation time
          3. Continuous operation distance
          Drive information 3
          1. Coolant temperature gauge
          2. Oil temperature gauge
          3. Voltage gauge
          Driving Assist System Information
          G meter
          1. G ball (past 20 items)*
          2. Steering angle gauge
          3. Brake pedal force
          4. Accelerator position
          G meter and peak hold
          1. G ball (with peak hold)*
          2. Steering angle gauge
          3. Brake pedal force
          4. Accelerator position
          Torque curve
          1. Torque curve
          2. Power curve
          Stop watch (Lap timer)

          HINT:
          *: This display is intended for use as a guideline. Depending on factors such as the road surface condition, temperature and vehicle speed, the display may not show the actual condition of the vehicle.