Home › Brake › BRAKE (REAR) › REAR BRAKE

REAR BRAKE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for RH and LH sides.
  2. The procedure listed below is for LH side.



1. INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH


    C261030
  1. Apply a light layer of lithium soap base glycol grease to the inner face of a new rear disc brake cylinder slide bush.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake cylinder slide bush.

  1. Install the 2 rear disc brake cylinder slide bushes to the caliper support bracket.



2. INSTALL REAR DISC BRAKE REAR CYLINDER SLIDE PIN


    C261031E01
  1. Apply a light layer of lithium soap base glycol grease to the contact face between a new bush and rear disc brake rear cylinder rear disc brake cylinder slide pin.
    Text in Illustration 
    *1
    rear disc brake rear cylinder rear disc brake cylinder slide pin
    *2
    Bush
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the new bush to the rear disc brake rear cylinder rear disc brake cylinder slide pin.

  1. Apply a light layer of lithium soap base glycol grease to entire circumference of the rear disc brake rear cylinder rear disc brake cylinder slide pin and fitting part.

  1. Install the rear disc brake rear cylinder rear disc brake cylinder slide pin to the caliper support bracket.



3. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN


    C261032
  1. Apply a light layer of lithium soap base glycol grease to entire circumference of the rear disc brake cylinder slide pin and fitting part.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the rear disc brake cylinder slide pin to the caliper support bracket.



4. INSTALL REAR DISC
  1. Align the matchmarks placed when removing, install the rear disc to the axle hub.

    HINT:
    When using a new rear disc, install it so that rear disc runout is minimum.



5. ADJUST PARKING BRAKE


6. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug to the rear disc.



7. INSTALL CALIPER SUPPORT BRACKET
  1. Install the caliper support bracket with the 2 new bolts.

    Torque:
    66 N*m{ 673 kgf*cm , 49 ft.*lbf }



    C256672
  1. Apply a light of lithium soap base glycol grease to contact section of the rear disc brake pad support plate with the rear disc brake pad.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease



8. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE


    C256671
  1. Apply a light of lithium soap base glycol grease to contact section of the rear disc brake pad support plate with the rear disc brake pad.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the rear disc brake pad support plate to the caliper support bracket.



9. INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT


    C261033E01
  1. Apply disc brake grease to the rear disc brake anti squeal shim kit.
    Text in Illustration 
    *A
    Solid Disc Brake
    *B
    Ventilated Disc Brake
    *1
    Rear Disc Brake Pad Kit
    *2
    Rear Disc Brake Anti Squeal Shim Kit
    V100135
    Disc Brake Grease

  1. Put the rear disc anti squeal shim kit to each rear disc brake pad.



10. INSTALL REAR DISC BRAKE PAD KIT
  1. Install the rear disc brake pad kit to the caliper support bracket.



11. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH
  1. Apply the rear disc brake cylinder assembly LH to the caliper support bracket.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



12. CONNECT REAR FLEXIBLE HOSE LH
  1. Connect the rear left flexible hose with 2 new gaskets and the new union bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



13. ADD BRAKE FLUID
  1. Remove the brake master cylinder reservoir filler cap.

  1. Fill the reservoir with brake fluid.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    NOTICE:
    Make sure that there is sufficient brake fluid in the reservoir.



14. BLEED BRAKE LINE


C256648

NOTICE:
  1. Bleed the brake line of the wheel farthest from the master cylinder first.
  2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brake lines.

  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1

  1. When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2

  1. Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and a new brake fluid comes out.

  1. Tighten the bleeder plug completely.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Repeat the above steps to replace the brake fluid of the brake lines for each wheel.



15. INSPECT BRAKE FLUID LEAK


16. INSPECT FLUID LEVEL


    C259961E01
  1. Check the fluid level.
    Text in Illustration 
    *a
    MAX Line
    *b
    MIN Line
    If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    NOTICE:
    If using a dropper to adjust the fluid amount, make sure that the dropper has not been used with mineral oils, water or deteriorated brake fluid. Sealed areas may deteriorate and lead to fluid leaks, or the fluid may deteriorate and lead to decreased efficiency.



17. INSTALL REAR WHEEL

Torque:
120 N*m{ 1224 kgf*cm , 89 ft.*lbf }