Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here


HINT:
Use the same procedure for the RHD and LHD vehicle.



1. REMOVE WINDSHIELD WIPER ARM COVER


    B314860E01
  1. Using a screwdriver, disengage the claw and remove the windshield wiper arm cover, as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for both the RH and LH sides.



2. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH


    B314861
  1. Remove the nut and the windshield wiper arm and blade assembly LH.



3. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH


    B314862
  1. Remove the nut and the windshield wiper arm and blade assembly RH.



4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    B309212
  1. Disengage the 4 claws.

  1. Remove the clip and the front fender to cowl side seal RH.



5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:
The procedure described below is for the RH side.



6. REMOVE COWL VENTILATOR LOUVER
  1. Using a clip remover, remove the 3 clips.



  1. While pressing the claws, as shown in the illustration, remove the 4 cowl top ventilator louver clips.


    B314863E01


    Text in Illustration 
    *1
    Cowl Top Ventilator Louver Clip
    -
    -

    NOTICE:
    Do not pull forcibly the cowl top ventilator louver clips because they may get damaged.

  1. Disengage the 15 guides and pull out the cowl ventilator louver, as shown in the illustration.



7. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step. Refer to the following procedures .



8. REMOVE WINDSHIELD GLASS


    B309158E01
  1. Apply protective tape to the installation position of the windshield glass on the vehicle body.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Apply protective tape to the area around installation surface to prevent it from being scratched.



    B187142E06
  1. Using a knife, cut off the windshield moulding outside, as shown in the illustration.
    Text in Illustration  
    *1
    Body
    *2
    Windshield moulding outside
    *3
    Windshield glass
    *a
    Cut

    CAUTION:
    1. Do not damage the vehicle body with the knife.
    2. If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the windshield glass.



    B309159E01
  1. Place matchmarks on the windshield glass and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *a
    Matchmark

    HINT:
    Matchmarks are not necessary if the windshield glass is not going to be reused.



    B313102E01
  1. Pass a piano wire between the vehicle body and windshield glass from the interior, as shown in the illustration.
    Text in Illustration 
    *1
    Wooden Block
    *2
    Plastic Sheet
    *3
    Windshield Glass Stopper
    *4
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the windshield glass.

    NOTICE:
    1. When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
    3. Do not damage the windshield glass.



    B309162E01
  1. Using suction cups, disengage the windshield glass stopper and remove the windshield glass.
    Text in Illustration 
    *1
    Windshield Glass Stopper

    NOTICE:
    1. There are windshield glass stopper on the windshield glass, as shown in the illustration. Be careful not to damage the windshield glass stopper when cutting off the adhesive.
    2. To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.



9. REMOVE WINDOW GLASS ADHESIVE DAM


    B309163E01
  1. Using a scraper, remove the window glass adhesive dam.
    Text in Illustration 
    *1
    Window Glass Adhesive Dam
    *a
    Back Side

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the window glass adhesive dam with a new one.



10. REMOVE LOWER WINDSHIELD GLASS SEAL


    B309163E02
  1. Using a scraper, remove the 2 windshield glass seals.
    Text in Illustration 
    *1
    Windshield Glass Seal
    *a
    Back Side

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the lower windshield glass seal with a new one.



11. REMOVE WINDSHIELD OUTSIDE MOULDING


    B309164E01
  1. Using a scraper, remove the windshield outside moulding with the upper windshield glass seal.
    Text in Illustration 
    *1
    Windshield Outside Moulding
    *a
    Back Side

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the windshield outside moulding with a new one.



12. REMOVE UPPER WINDSHIELD GLASS SEAL

NOTICE:
Be sure to replace the upper windshield glass seal with a new one.



13. REMOVE NO. 1 WINDSHIELD GLASS STOPPER


    B309165E01
  1. Using a scraper, remove the No. 1 windshield glass stopper.
    Text in Illustration 
    *1
    No. 1 Windshield Stopper
    *2
    No. 2 Windshield Stopper
    *a
    Back Side

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the No. 1 windshield glass stopper with a new one.



14. REMOVE NO. 2 WINDSHIELD GLASS STOPPER

HINT:
Use the same procedure as for the No. 1 windshield glass stopper.



15. CLEAN WINDSHIELD GLASS


    B149736
  1. Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.

    NOTICE:
    Be careful not to damage the windshield glass.

  1. Clean the outer circumference of the windshield glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.



16. CLEAN VEHICLE BODY


  1. Clean and shape the contact surfaces of the vehicle body.



    1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.



      B309172E01


      Standard Dimension:

      Area
      Dimension
      a
      2.0 mm (0.0787 in.)


      Text in Illustration 
      *1
      Body
      -
      -
      V100145
      Adhesive
      -
      -

    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.