Home › Drivetrain ยท TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE REFILL PLUG
  1. Remove the refill plug.

  1. Remove the O-ring from the refill plug.



2. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH


    C263924
  1. Remove the nut, spring washer and the transmission control shaft lever RH from the park/neutral position switch assembly.



3. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C263925
  1. Using a screwdriver, bend the tabs of the lock washer.

  1. Remove the nut and the lock washer.

  1. Remove the bolt and the park/neutral position switch assembly from the automatic transmission case sub-assembly.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.



4. REMOVE OIL COOLER TUBE UNION


    C263936
  1. Remove the 2 oil cooler tube union from the automatic transmission case sub-assembly.



5. REMOVE TRANSMISSION REVOLUTION SENSOR


    C230501
  1. Remove the 2 bolts and the 2 transmission revolution sensors from the automatic transmission case sub-assembly.

  1. Remove the 2 O-rings from the 2 transmission revolution sensors.



6. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE


    C109351
  1. Remove the 2 bolts and the automatic transmission breather tube from the automatic transmission case sub-assembly.



7. REMOVE AUTOMATIC TRANSMISSION CASE PLUG


    C235143
  1. Remove the 5 automatic transmission case plugs from the automatic transmission case sub-assembly.

  1. Remove the 5 O-rings from the 5 automatic transmission case plugs.



    C235144
  1. Using "TORX" socket wrench T55, remove the automatic transmission case plug from the automatic transmission case sub-assembly.

  1. Remove the O-ring from the automatic transmission case plug.



8. REMOVE AUTOMATIC TRANSMISSION HOUSING


    C263937
  1. Remove the 10 bolts and the automatic transmission housing from the automatic transmission case sub-assembly.



9. REMOVE EXTENSION HOUSING DUST DEFLECTOR


    C122826
  1. Using a brass bar and a hammer, tap out the extension housing dust deflector from the extension housing sub-assembly.

    NOTICE:
    Be careful not to damage the extension housing sub-assembly.



10. REMOVE EXTENSION HOUSING SUB-ASSEMBLY


    C106925
  1. Remove the 6 bolts.



    C228258E01
  1. Using a screwdriver, remove the extension housing sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not pry the surface where the extension housing sub-assembly contacts the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



11. REMOVE TRANSMISSION CASE ADAPTER RADIAL BALL BEARING


    C106927
  1. Using snap ring pliers, remove the snap ring from the extension housing sub-assembly.

  1. Remove the transmission case adapter radial ball bearing from the extension housing sub-assembly.



12. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL


    C228259E01
  1. Using a screwdriver, pry out the automatic transmission extension housing oil seal from the extension housing sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the extension housing sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE OUTPUT SHAFT THRUST BEARING


    C106923
  1. Using a snap ring expander, remove the snap ring from the output shaft of the rear planetary gear assembly.

  1. Remove the rear output shaft thrust bearing race, output shaft thrust bearing and the output shaft thrust bearing race.



14. SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY


    D031356E01
  1. Install the automatic transmission case sub-assembly to an overhaul attachment.



15. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the oil pan.

  1. Using a socket hexagon wrench 5 mm, remove the overflow plug and gasket.

  1. Remove the drain plug and gasket.



    C256218
  1. Remove the 20 bolts, automatic transmission oil pan sub-assembly and the automatic transmission oil pan gasket.



    C109359E04
  1. Remove the 3 transmission oil cleaner magnets from the automatic transmission oil pan sub-assembly.
    Text in Illustration 
    *1
    Transmission Oil Cleaner Magnet

  1. Examine the particles in the automatic transmission oil pan sub-assembly.

    1. Collect any steel chips with the removed transmission oil cleaner magnets. Carefully inspect the foreign matter and particles in the automatic transmission oil pan sub-assembly and on the transmission oil cleaner magnets to anticipate the type of wear you will find in the automatic transmission assembly.
      Steel (magnetic): bearing, gear and clutch plate wear
      Brass (non-magnetic): bush wear



16. REMOVE VALVE BODY OIL STRAINER ASSEMBLY
  1. Turn over the automatic transmission case sub-assembly.



    C258476
  1. Remove the 4 bolts and the valve body oil strainer assembly from the transmission valve body assembly.



    C258477E01
  1. Remove the O-ring from the valve body oil strainer assembly.
    Text in Illustration 
    *1
    O-ring



17. REMOVE TRANSMISSION WIRE


    C231586
  1. Remove the bolt and the temperature sensor clamp, and separate the ATF temperature sensor.



    C257575
  1. Remove the bolt and the valve body wire harness clamp.

  1. Disengage the wire harness clamp.



    C122840
  1. Disconnect the 9 solenoid valve connectors.



    C099927E01
  1. Remove the bolt and pull out the transmission wire.



    C101505E05
  1. Remove the O-ring from the transmission wire.
    Text in Illustration 
    *1
    O-ring



18. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C106931
  1. Remove the bolt, detent spring cover and the detent spring from the transmission valve body assembly.



    C106932
  1. Remove the 19 bolts and the transmission valve body assembly from the automatic transmission case sub-assembly.



    C109330E07
  1. Disconnect the manual valve connecting rod sub-assembly from the manual valve lever sub-assembly.
    Text in Illustration 
    *1
    Manual Valve Connecting Rod Sub-assembly
    *2
    Manual Valve Lever Sub-assembly



19. REMOVE TRANSMISSION CASE GASKET


    D027968E03
  1. Remove the 3 transmission case gaskets from the automatic transmission case sub-assembly.



20. REMOVE BRAKE DRUM GASKET


    D027969E01
  1. Remove the 3 brake drum gaskets from the automatic transmission case sub-assembly.



21. REMOVE CHECK BALL BODY


    D027914E13
  1. Remove the check ball body and the compression spring from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Check Ball Body
    *2
    Compression Spring



22. REMOVE C-2 ACCUMULATOR PISTON


    D027915E01
  1. While blowing compressed air into the oil hole, remove the C-2 accumulator piston and the spring from the automatic transmission case sub-assembly.

    NOTICE:
    Take care as the C-3 and B-3 accumulator pistons may jump out.

  1. Remove the 2 O-rings from the C-2 accumulator piston.



    C224346
  1. Using a screwdriver, remove the snap ring and the spring sub-assembly from the C-2 accumulator piston.

    NOTICE:
    Be careful not to damage the C-2 accumulator piston.

    HINT:
    Tape the screwdriver tip before use.



23. REMOVE B-3 ACCUMULATOR PISTON
  1. While blowing compressed air into the oil hole, remove the B-3 accumulator piston and the spring from the automatic transmission case sub-assembly.

    NOTICE:
    Take care as the C-3 accumulator piston may jump out.

  1. Remove the 2 O-rings from the B-3 accumulator piston.



    C224346
  1. Using a screwdriver, remove the snap ring and the spring sub-assembly from the B-3 accumulator piston.

    NOTICE:
    Be careful not to damage the B-3 accumulator piston.

    HINT:
    Tape the screwdriver tip before use.



24. REMOVE C-3 ACCUMULATOR PISTON


    D027916E01
  1. While blowing compressed air into the oil hole, remove the C-3 accumulator piston and the 2 springs from the automatic transmission case sub-assembly.

  1. Remove the 2 O-rings from the C-3 accumulator piston.



25. REMOVE B-1 ACCUMULATOR VALVE


    C122853
  1. Remove the B-1 accumulator valve and the spring from the automatic transmission case sub-assembly.



26. REMOVE PARKING LOCK PAWL BRACKET


    D031361E01
  1. Remove the 3 bolts and the parking lock pawl bracket from the automatic transmission case sub-assembly.



27. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    D031551E01
  1. Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.



28. REMOVE PARKING LOCK PAWL SHAFT


    C122830E04
  1. Pull out the parking lock pawl shaft from the front side, and remove the parking lock pawl and the torsion spring.
    Text in Illustration 
    *1
    Parking Lock Pawl
    *2
    E-ring
    *3
    Parking Lock Pawl Shaft
    *4
    Torsion Spring

  1. Remove the E-ring from the parking lock pawl shaft.



29. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    C230643E02
  1. Using a screwdriver and a hammer, cut off the spacer and remove it from the manual valve lever shaft.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the manual valve lever shaft.

    HINT:
    Tape the screwdriver tip before use.



    C106933
  1. Using a pin punch 3 mm and a hammer, drive out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the automatic transmission case sub-assembly.

  1. Pull the manual valve lever shaft out through the case and remove the manual valve lever sub-assembly.



30. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C210559E02
  1. Using a screwdriver, pry out the 2 manual valve lever shaft oil seals from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



31. REMOVE OIL PUMP ASSEMBLY


    C106934
  1. Remove the 9 bolts.



    C106935E04
  1. Using a screwdriver, pull out the oil pump assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the oil pump assembly or automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    C122832E04
  1. Remove the No. 1 thrust bearing race from the oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Thrust Bearing Race
    *2
    Oil Pump Assembly
    *3
    O-ring

  1. Remove the O-ring from the oil pump assembly.



32. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    D027923E01
  1. Remove the clutch drum and input shaft assembly from the automatic transmission case sub-assembly.



    C109327E09
  1. Remove the clutch drum thrust washer, thrust needle roller bearing, input shaft front thrust bearing race and the input shaft front thrust needle roller bearing from the clutch drum and input shaft assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Input Shaft Front Thrust Bearing Race
    *3
    Input Shaft Front Thrust Needle Roller Bearing
    *4
    Clutch Drum Thrust Washer



33. REMOVE NO. 2 ONE-WAY CLUTCH ASSEMBLY


    D027994E06
  1. Remove the No. 2 one-way clutch assembly and the input shaft clutch drum thrust washer from the clutch drum and input shaft assembly.
    Text in Illustration 
    *1
    No. 2 One-way Clutch Assembly
    *2
    Input Shaft Clutch Drum Thrust Washer



34. SUPPORT CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    D031375E06
  1. Place the oil pump assembly onto the torque converter assembly, and then place the clutch drum and input shaft assembly onto the oil pump assembly.
    Text in Illustration 
    *1
    Torque Converter Assembly
    *2
    Oil Pump Assembly



35. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY


    D027996E04
  1. Using a screwdriver, remove the snap ring from the reverse clutch piston sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the reverse clutch piston sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    D027997E01
  1. Remove the reverse clutch hub sub-assembly from the reverse clutch drum sub-assembly.



36. REMOVE REVERSE CLUTCH REACTION SLEEVE


    D027998E01
  1. Remove the reverse clutch reaction sleeve from the reverse clutch hub sub-assembly.



37. REMOVE NO. 3 CLUTCH DISC (REAR CLUTCH DISC)


    C122852E03
  1. Remove the clutch cushion plate, reverse clutch flange, 4 No. 3 clutch discs and the 3 No. 3 clutch plates from the reverse clutch hub sub-assembly.
    Text in Illustration 
    *1
    No. 3 Clutch Disc
    *2
    No. 3 Clutch Plate
    *3
    Reverse Clutch Flange
    *4
    Clutch Cushion Plate



38. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


    D031376E03
  1. Remove the forward clutch hub sub-assembly and the No. 3 clutch hub thrust washer from the reverse clutch drum sub-assembly.
    Text in Illustration 
    *1
    Forward Clutch Hub Sub-assembly
    *2
    No. 3 Clutch Hub Thrust Washer



    C109367E10
  1. Remove the 2 thrust needle roller bearings and the No. 2 thrust bearing race from the forward clutch hub sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    No. 2 Thrust Bearing Race



39. REMOVE COAST CLUTCH HUB SUB-ASSEMBLY


    D031377E02
  1. Remove the coast clutch hub sub-assembly from the reverse clutch drum sub-assembly.



40. REMOVE NO. 4 ONE-WAY CLUTCH ASSEMBLY


    C109362E04
  1. Remove the No. 4 one-way clutch assembly and the No. 2 clutch hub thrust washer from the coast clutch hub sub-assembly.
    Text in Illustration 
    *1
    Coast Clutch Hub Sub-assembly
    *2
    No. 2 Clutch Hub Thrust Washer
    *3
    No. 4 One-way Clutch Assembly



41. REMOVE NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)


    D031378E03
  1. Using a screwdriver, remove the snap ring.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the input shaft.

    HINT:
    Tape the screwdriver tip before use.



    C109356E04
  1. Remove the forward clutch flange, 4 No. 1 clutch discs, 4 No. 1 clutch plates and the clutch cushion plate from the input shaft.
    Text in Illustration 
    *1
    Clutch Cushion Plate
    *2
    No. 1 Clutch Plate
    *3
    No. 1 Clutch Disc
    *4
    Forward Clutch Flange



42. REMOVE NO. 4 CLUTCH DISC (COAST CLUTCH DISC)


    D031380E04
  1. Using a screwdriver, remove the snap ring.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the forward clutch piston sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    C112967E03
  1. Remove the coast clutch flange, 4 No. 4 clutch discs and the 4 No. 4 clutch plates from the forward clutch piston sub-assembly.
    Text in Illustration 
    *1
    No. 4 Clutch Plate
    *2
    No. 4 Clutch Disc
    *3
    Coast Clutch Flange



43. REMOVE INPUT SHAFT


    C109352E06
  1. Remove the thrust needle roller bearing and the input shaft rear thrust bearing race from the input shaft.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Input Shaft Rear Thrust Bearing Race



    D031522E01
  1. Remove the input shaft from the reverse clutch drum sub-assembly.



44. REMOVE CLUTCH DRUM OIL SEAL RING


    D031399E01
  1. Remove the 4 clutch drum oil seal rings from the input shaft.



45. REMOVE NO. 1 CLUTCH BALANCER


    C261812E01
  1. Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.

    SST
    09387-00110  

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



    C109343E01
  1. Remove the No. 1 clutch balancer and the forward clutch return spring sub-assembly from the input shaft.
    Text in Illustration 
    *1
    No. 1 Clutch Balancer
    *2
    Forward Clutch Return Spring Sub-assembly



    C109344E02
  1. Remove the D-ring from the No. 1 clutch balancer.
    Text in Illustration 
    *1
    D-ring



46. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY


    D031400E01
  1. Hold the forward clutch piston sub-assembly and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the input shaft to remove the forward clutch piston sub-assembly.



    D031383E03
  1. Remove the coast clutch piston from the forward clutch piston sub-assembly.
    Text in Illustration 
    *1
    Coast Clutch Piston
    *2
    Forward Clutch Piston Sub-assembly



    C141896E01
  1. Remove the O-ring from the input shaft.
    Text in Illustration 
    *1
    O-ring



47. REMOVE REVERSE CLUTCH FLANGE


    D028506E01
  1. Remove the reverse clutch flange from the reverse clutch drum sub-assembly.



48. REMOVE NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)


    D028507E03
  1. Using a screwdriver, remove the 2 snap rings from the reverse clutch drum sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the reverse clutch drum sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    C109338E03
  1. Remove the direct clutch flange, 5 No. 2 clutch discs and the 5 No. 2 clutch plates from the reverse clutch drum sub-assembly.
    Text in Illustration 
    *1
    No. 2 Clutch Plate
    *2
    No. 2 Clutch Disc
    *3
    Direct Clutch Flange



49. REMOVE NO. 3 CLUTCH BALANCER


    D028509E04
  1. Place SST on the No. 3 clutch balancer, and compress the reverse clutch return spring sub-assembly with a press.

    SST
    09387-00070  

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the No. 3 clutch balancer.



50. REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D028510E05
  1. Remove the reverse clutch return spring sub-assembly and O-ring from the reverse clutch piston sub-assembly.
    Text in Illustration 
    *1
    Reverse Clutch Return Spring Sub-assembly
    *2
    O-ring
    *3
    Reverse Clutch Piston Sub-assembly



51. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY


    D028511E02
  1. Remove the reverse clutch piston sub-assembly from the reverse clutch drum sub-assembly.
    Text in Illustration 
    *1
    Reverse Clutch Piston Sub-assembly
    *2
    Reverse Clutch Drum Sub-assembly



    D028512E03
  1. Remove the O-ring from the reverse clutch piston sub-assembly.
    Text in Illustration 
    *1
    O-ring



    D028513E03
  1. Remove the O-ring from the reverse clutch drum sub-assembly.
    Text in Illustration 
    *1
    O-ring



52. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    D031401E01
  1. Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.

    SST
    09320-89010  

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



    C109370E01
  1. Remove the No. 2 clutch balancer and the direct clutch return spring sub-assembly.
    Text in Illustration 
    *1
    No. 2 Clutch Balancer
    *2
    O-ring
    *3
    Direct Clutch Return Spring Sub-assembly

  1. Remove the O-ring from the No. 2 clutch balancer.



    D028515E03
  1. Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the reverse clutch drum sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the direct clutch piston sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    D028816E03
  1. Remove the 2 O-rings from the direct clutch piston sub-assembly.
    Text in Illustration 
    *1
    O-ring



53. REMOVE NO. 3 BRAKE DISC (2ND BRAKE DISC SET)


    C230646E02
  1. Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    C122833E02
  1. Remove the No. 3 brake flange, 3 No. 3 brake discs and the 3 No. 3 brake plates from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 3 Brake Plate
    *2
    No. 3 Brake Disc
    *3
    No. 3 Brake Flange



54. REMOVE 2ND BRAKE CYLINDER


    D027927E10
  1. Using SST, remove the snap ring from the automatic transmission case sub-assembly.

    SST
    09350-30020   (09350-07060)



    C108608
  1. Remove the 2nd brake cylinder from the automatic transmission case sub-assembly.



55. REMOVE 2ND BRAKE PISTON


    C256937E02
  1. Using a screwdriver, remove the snap ring and the No. 3 brake piston return spring sub-assembly from the 2nd brake cylinder.
    Text in Illustration 
    *1
    Snap Ring
    *2
    No. 3 Brake Piston Return Spring Sub-assembly
    *3
    2nd Brake Cylinder

    NOTICE:
    Be careful not to damage the 2nd brake cylinder.

    HINT:
    Tape the screwdriver tip before use.



    D028545E01
  1. Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.



    D028546E14
  1. Remove the 2 O-rings from the 2nd brake piston.
    Text in Illustration 
    *1
    O-ring



56. REMOVE ONE-WAY CLUTCH ASSEMBLY


    D027928E04
  1. Remove the one-way clutch assembly and the No. 1 planetary carrier thrust washer from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    No. 1 Planetary Carrier Thrust Washer



57. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D027930E04
  1. Remove the front planetary gear assembly and the one-way clutch inner race sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    One-way Clutch Inner Race Sub-assembly
    *2
    Front Planetary Gear Assembly



    D027931E17
  1. Remove the front planetary flange rear thrust bearing race, front planetary flange thrust needle roller bearing and the No. 2 planetary carrier thrust washer from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Front Planetary Flange Rear Thrust Bearing Race
    *2
    Front Planetary Flange Thrust Needle Roller Bearing
    *3
    No. 2 Planetary Carrier Thrust Washer



58. REMOVE FRONT PLANETARY RING GEAR


    C108586
  1. Remove the front planetary ring gear from the automatic transmission case sub-assembly.



59. REMOVE CENTER PLANETARY RING GEAR


    C230647E01
  1. Using a screwdriver, remove the snap ring.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the front planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the center planetary ring gear from the front planetary ring gear.



    C230648E01
  1. Using a screwdriver, remove the snap ring.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the center planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the front planetary ring gear flange sub-assembly from the center planetary ring gear.



60. REMOVE NO. 1 BRAKE DISC


    C230500E02
  1. Remove the No. 1 brake flange, 3 No. 1 brake discs and the 3 No. 1 brake plates from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 1 Brake Plate
    *2
    No. 1 Brake Disc
    *3
    No. 1 Brake Flange



61. REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C230650E02
  1. Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    D027935E05
  1. Remove the brake piston return spring sub-assembly and the No. 1 brake cylinder from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Brake Piston Return Spring Sub-assembly
    *2
    No. 1 Brake Cylinder



62. REMOVE NO. 1 BRAKE PISTON


    D027936E01
  1. Hold the No. 1 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 1 brake cylinder to remove the No. 1 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 1 brake piston.



63. REMOVE NO. 2 BRAKE DISC


    C230651E02
  1. Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    D031547E07
  1. Remove the 2 No. 2 brake flanges, 4 No. 2 brake discs, 3 No. 2 brake plates and the No. 2 brake piston return spring sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Disc
    *3
    No. 2 Brake Plate
    *4
    No. 2 Brake Piston Return Spring Sub-assembly



64. REMOVE NO. 2 BRAKE PISTON


    D027939E01
  1. Hold the No. 2 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston and the No. 2 brake cylinder.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the No. 2 brake piston from the No. 2 brake cylinder.

  1. Remove the 2 O-rings from the No. 2 brake piston.



65. REMOVE CENTER PLANETARY GEAR ASSEMBLY


    C256936E01
  1. Remove the center planetary gear assembly, planetary sun gear, thrust needle roller bearing and the No. 4 thrust bearing race from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    No. 4 Thrust Bearing Race
    *3
    Center Planetary Gear Assembly
    *4
    Planetary Sun Gear



66. REMOVE INTERMEDIATE SHAFT


    D031365E04
  1. Using SST, remove the snap ring from the automatic transmission case sub-assembly.

    SST
    09350-30020   (09350-07060)



    D027942E01
  1. Remove the intermediate shaft together with the No. 3 one-way clutch assembly from the automatic transmission case sub-assembly.



67. REMOVE NO. 3 ONE-WAY CLUTCH ASSEMBLY


    D027964E03
  1. Remove the No. 3 one-way clutch assembly and the one-way clutch inner race from the intermediate shaft.
    Text in Illustration 
    *1
    No. 3 One-way Clutch Assembly
    *2
    One-way Clutch Inner Race



68. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    C108607E07
  1. Remove the rear planetary ring gear flange sub-assembly, No. 7 thrust bearing race, thrust needle roller bearing and the No. 8 thrust bearing race from the intermediate shaft.
    Text in Illustration 
    *1
    Rear Planetary Ring Gear Flange Sub-assembly
    *2
    No. 7 Thrust Bearing Race
    *3
    Thrust Needle Roller Bearing
    *4
    No. 8 Thrust Bearing Race



69. REMOVE BRAKE PLATE STOPPER SPRING


    D027943E01
  1. Remove the brake plate stopper spring from the automatic transmission case sub-assembly.



70. REMOVE NO. 4 BRAKE DISC


    C230499E01
  1. Remove the 2 No. 4 brake flanges, 5 No. 4 brake discs and the 4 No. 4 brake plates from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 4 Brake Flange
    *2
    No. 4 Brake Disc
    *3
    No. 4 Brake Plate



71. REMOVE REAR PLANETARY GEAR ASSEMBLY


    C109346
  1. Remove the rear planetary gear assembly from the automatic transmission case sub-assembly.



    C109347E06
  1. Remove the thrust bearing race, thrust needle roller bearing and the No. 9 thrust bearing race from the rear planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing
    *3
    No. 9 Thrust Bearing Race



    D027947E01
  1. Remove the thrust needle roller bearing from the automatic transmission case sub-assembly.



72. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C108601E03
  1. Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly.
    Text in Illustration 
    *1
    Snap Ring

    SST
    09350-30020   (09350-07050)

  1. Using SST, remove the snap ring and the 1st and reverse brake return spring sub-assembly.

    SST
    09350-30020   (09350-07070)



73. REMOVE BRAKE APPLY TUBE


    C108599
  1. Remove the brake apply tube from the automatic transmission case sub-assembly.



74. REMOVE 1ST AND REVERSE BRAKE PISTON


    C108598
  1. Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the 1st and reverse brake piston.



75. REMOVE BRAKE REACTION SLEEVE


    C108602E01
  1. Using SST, remove the brake reaction sleeve from the automatic transmission case sub-assembly.

    SST
    09350-30020   (09350-07080)

  1. Remove the 2 O-rings from the brake reaction sleeve.



76. REMOVE NO. 4 BRAKE PISTON


    C108603E01
  1. Using SST, remove the No. 4 brake piston from the automatic transmission case sub-assembly.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the No. 4 brake piston.