Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A281924E01

HINT:
The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of the terminals, and displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A33-1 (+B2) - A36-4 (E01)
V - B-L
Power source of ECM
Ignition switch ON
12 to 14 V
A33-2 (BATT) - A36-4 (E01)
W - B-L
Battery(for measuring battery voltage and for ECM memory)
Always
10 to 13 V
A33-3 (ST1-) - A36-4 (E01)
BR-B - B-L
Stop light switch
Brake pedal depressed
11 to 14 V
Brake pedal released
0 to 1 V
A33-7 (STP) - A36-4 (E01)
R - B-L
Stop light switch
Brake pedal depressed
0 to 1 V
Brake pedal released
11 to 14 V
A33-8 (ACP) - A36-4 (E01)*5
G - B-L
Air conditioner pressure sensor
Ignition switch ON with A/C on
0 to 1 V
Idling with A/C off
12 to 14 V
A33-12 (THA) - A36-29 (E1)
BR-G - Y-B
Intake air temperature sensor
(built into mass air flow meter)
Ignition switch ON
0.3 to 4.6 V
A33-14 (STSW2) - A36-4 (E01)*3
BR - B-L
Starter signal
Ignition switch ON
0 to 1 V
Cranking
6 to 13 V
A33-15 (CLSW) - A36-4 (E01)*2
R-Y - B-L
Clutch switch
Ignition switch ON with clutch pedal depressed
0 to 1 V
Ignition switch ON with clutch pedal released
10 to 13 V
A33-16 (NSW) - A36-4 (E01)
W-R - B-L*1
G-B - B-L*2
Neutral switch signal
Ignition switch ON, shift lever in P or N*1
Ignition switch ON, shift lever in Neutral*2
0 to 1 V
Ignition switch ON, shift lever not in P or N*1
Ignition switch ON, shift lever not in Neutral*2
10 to 13 V
A33-17 (STSW) - A36-4 (E01)*3
G-W - B-L
Starter signal from certification ECU (smart key ECU assembly*3)
Ignition switch ON
0 to 1 V
Cranking
Over 6 V
A33-17 (STSW2) - A36-4 (E01)*4
BR - B-L
Starter signal
Ignition switch ON
0 to 1 V
Cranking
6 to 13 V
A33-18 (CANL) - A36-4 (E01)
B-P - B-L
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 1)
A33-19 (CANH) - A36-4 (E01)
O - B-L
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 2)
A33-20 (HB) - A36-4 (E01)*10
G-Y - B-L
BLOWER relay
Ignition switch ON with blower fan switch on
0 to 1 V
Ignition switch ON with blower fan switch off
10 to 13 V
A33-22 (VG) - A33-29 (E2G)
Y - B-G
Mass air flow meter
Idling with warm engine
0.9 to 4.5 V
A33-27 (IGSW) - A36-4 (E01)
GR - B-L
IG2 relay
Ignition switch ON
10 to 13 V
A34-5 (HA1A) - A36-4 (E01)
R-L - B-L
Air fuel ratio sensor heater
Idling with cold engine
Pulse generation
(See waveform 3)
A34-6 (+B) - A36-4 (E01)
V - B-L
Power source of ECM
Ignition switch ON
12 to 14 V
A34-9 - A36-29 (E1)
V-B - Y-B
Fuel pressure sensor
Idling with warm engine
0.7 to 1.3 V
A34-11 (IJF1) - A36-4 (E01)
R-Y - B-L
Injector for direct injection confirmation signal
Idling
Pulse generation
(See waveform 4)
A34-13 (FPF) - A36-4 (E01)
R-B - B-L
High pressure side fuel pump (Spill valve)
Idling
Pulse generation
(See waveform 5)
A34-14 (EV1+) - A36-4 (E01)
Y-BR - B-L
Variable valve timing (VVT) sensor (Exhaust side (bank 1))
Idling with warm engine
Pulse generation
(See waveform 6)
A34-15 (VV2+) - A36-4 (E01)
Y-V - B-L
Variable valve timing (VVT) sensor (Intake side (bank 2))
Idling with warm engine
Pulse generation
(See waveform 7)
A34-16 (NE+) - A34-27 (NE-)
W - B
Crank position sensor
Idling with warm engine
Pulse generation
(See waveform 6 or 7)
A34-17 (KNK2) - A36-29 (E1)
G - Y-B
Knock sensor
Ignition switch ON
Approximately 2.5 V
A34-18 (A1A-) - A36-4 (E01)
O - B-L
Air fuel ratio sensor
Ignition switch ON
2.4 to 2.7 V
A34-19 (A1A+) - A36-4 (E01)
W - B-L
Air fuel ratio sensor
Ignition switch ON
2.8 to 3.2 V
A34-20 (PIM) - A36-29 (E1)
BR-B - Y-B
Intake manifold pressure sensor
Idling with warm engine
1.1 to 2.0 V
A34-21 (OX1B) - A36-4 (E01)
L-G - B-L*11
LG - B-L*12
Heated oxygen sensor
Idling with warm engine
0 to 0.9 V
A34-25 (EV2+) - A36-4 (E01)
BR-Y - B-L
Variable valve timing (VVT) sensor (Exhaust side (bank 2))
Idling with warm engine
Pulse generation
(See waveform 6)
A34-26 (VV1+) - A36-4 (E01)
Y-P - B-L
Variable valve timing (VVT) sensor (Intake side (bank 1))
Idling with warm engine
Pulse generation
(See waveform 7)
A34-28 (KNK1) - A36-29 (E1)
L - Y-B
Knock sensor
Ignition switch ON
Approximately 2.5 V
A34-31 (IJF2) - A36-4 (E01)
R-G - B-L
Injector for direct injection confirmation signal
Idling
Pulse generation
(See waveform 4)
A34-32 (FPD) - A36-4 (E01)
R-W - B-L
High pressure side fuel pump (Spill valve)
Idling
Pulse generation
(See waveform 5)
A34-34 (VVE) - A36-4 (E01)
G-B - B-L
Ground
Always
Below 1 Ω
A35-1 (VPMP) - A36-4 (E01)*9
P-L - B-L
Vent valve (built into canister pump module)
Ignition switch ON
10 to 13 V
A35-5 (IREL) - A36-4 (E01)
O-W - B-L
INJ relay
Idling
10 to 13 V
Ignition switch ON
0 to 1 V
A35-7 (+BM) - A36-4 (E01)
L-R - B-L
ETCS relay
Ignition switch ON
10 to 13 V
A35-8 (MPMP) - A36-4 (E01)*9
O-L - B-L
Leak detection pump (built into canister pump module))
Ignition switch ON
10 to 13 V
Leak detection pump ON
0 to 1 V
A35-10 (DI) - A36-4 (E01)
R-B - B-L
Fuel pump control (for fuel pump control malfunctioning detection)
Ignition switch ON
10 to 12 V
A35-11 (FAN2) - A36-4 (E01)*5
R-Y - B-L
FAN NO. 3 relay
Ignition switch ON
Cooling fan not operated
10 to 13 V
Idling with A/C on or High engine coolant temperature Cooling fan operated
0 to 0.5 V
A35-11 (FAN1) - A36-4 (E01)*6
B-R - B-L
FAN NO. 1 relay
Ignition switch ON
Cooling fan not operated
10 to 13 V
High engine coolant temperature Cooling fan operated
0 to 0.5 V
A35-12 (FAN1) - A36-4 (E01)*5
B-R - B-L
FAN NO. 2 relay
Ignition switch ON
10 to 13 V
Idling with A/C on or High engine coolant temperature Cooling fan operated
0 to 0.5 V
A35-13 (SSHUT) - A36-4 (E01)
LG - B-L
EFI MAIN1 relay
Ignition switch ON
0 to 1 V
A35-15 (TACH) - A36-4 (E01)*3
GR-R - B-L
Engine speed
Engine speed maintained at 1500 rpm
Pulse generation
(See waveform 8)
A35-17 (MCR) - A36-4 (E01)
R-L - B-L
ETCS relay
Ignition switch ON
0 to 1 V
A35-19 (FPC) - A36-4 (E01)
G-R - B-L
Fuel pump control
Ignition switch ON
Pulse generation
(See waveform 9)
A35-20 (PPMP) - A36-4 (E01)*9
O-B - B-L
Canister pressure sensor (built into canister pump module)
Ignition switch ON
1.5 to 4.0 V
A35-21 (VCPA) - A36-4 (E01)
L-Y - B-L
Power source of accelerator pedal position sensor
Ignition switch ON
4.5 to 5.5 V
A35-22 (VCP2) - A36-4 (E01)
G-B - B-L
Power source of accelerator pedal position sensor
Ignition switch ON
4.5 to 5.5 V
A35-23 (VPA) - A35-29 (EPA)
W - L
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
Approximately 0.7 V
Ignition switch ON, Accelerator pedal fully depressed
Approximately 3.1 V
A35-26 (STA) - A36-4 (E01)
B-W - B-L*7
B-L - B-L*8
ST relay
Ignition switch ON
10 to 13 V
Cranking
0 to 1 V
A35-31 (VPA2) - A35-30 (EPA2)
O - Y-B
Accelerator pedal position sensor (for sensor malfunctioning detection)
Ignition switch ON, Accelerator pedal fully released
Approximately 0.7 V
Ignition switch ON, Accelerator pedal fully depressed
Approximately 3.1 V
A35-32 (ACCR) - A36-4 (E01)*3
G-Y - B-L
ACC relay signal sent to certification ECU
Ignition switch ON
0 to 0.5 V
Cranking
12 to 14 V
A35-34 (STAR) - A36-4 (E01)*3
LG-R - B-L
ST CUT relay
Ignition switch ON
0 to 0.5 V
Cranking
8 to 13 V
A35-35 (AC) - A36-4 (E01)*5
L-O - B-L
HEATER relay
Idling with A/C on
0 to 0.5 V
Idling with A/C off
12 to 14 V
A36-1 (M-) - A36-4 (E01)
SB - B-L
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 10)
A36-2 (M+) - A36-4 (E01)
G-Y - B-L
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 10)
A36-5 (OE2) - A36-4 (E01)
BR-L - B-L
Camshaft timing oil control valve (OCV) (Exhaust side (bank 2))
Ignition switch ON
11 to 14 V
Idling with warm engine
Pulse generation
(See waveform 11)
A36-6 (HT1B) - A36-4 (E01)
R-B - B-L
Heated oxygen sensor heater
Ignition switch ON
11 to 14 V
Idling with cold engine
Pulse generation
(See waveform 12)
A36-7 (OE1) - A36-4 (E01)
R-W - B-L
Camshaft timing oil control valve (OCV) (Exhaust side (bank 1))
Ignition switch ON
11 to 14 V
Idling with warm engine
Pulse generation
(See waveform 11)
A36-8 (IGT4) - A36-4 (E01)
W-L - B-L
Ignition coil (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 13)
A36-10 (IGT2) - A36-4 (E01)
Y-R - B-L
Ignition coil (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 13)
A36-11 (PRG) - A36-4 (E01)
R-G - B-L
Purge valve
One of the following conditions is met:
  1. Ignition switch ON
  2. Idling with warm engine, under purge control
Pulse generation
(See waveform 14)
A36-12 (#10) - A36-4 (E01)
P - B-L
Injector for port injection
Idling with warm engine
Pulse generation
(See waveform 15)
A36-13 (#40) - A36-4 (E01)
P-G - B-L
Injector for port injection
Idling with warm engine
Pulse generation
(See waveform 15)
A36-14 (#1) - A36-4 (E01)
W - B-L
Injector for direct injection
Idling with warm engine
Pulse generation
(See waveform 4)
A36-16 (OC2) - A36-4 (E01)
GR - B-L
Variable valve timing (VVT) sensor (Intake side (bank 2))
Ignition switch ON
11 to 14 V
Idling with warm engine
Pulse generation
(See waveform 11)
A36-17 (OC1) - A36-4 (E01)
G-W - B-L
Variable valve timing (VVT) sensor (Intake side (bank 1))
Ignition switch ON
11 to 14 V
Idling with warm engine
Pulse generation
(See waveform 11)
A36-18 (VTA1) - A36-29 (E1)
LG - Y-B
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
Approximately 0.6 V
Ignition switch ON, Accelerator pedal fully depressed
Approximately 4.2 V
A36-19 (VC) - A36-29 (E1)
R - Y-B
Power source for sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
A36-20 (OT) - A36-29 (E1)
BR - Y-B
Oil temperature sensor
Idling
0.5 to 1.4 V
A36-21 (IGT1) - A36-4 (E01)
W-R - B-L
Ignition coil (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 13)
A36-22 (#20) - A36-4 (E01)
P-L - B-L
Injector for port injection
Idling with warm engine
Pulse generation
(See waveform 15)
A36-23 (#4) - A36-4 (E01)
LG-R - B-L
Injector for direct injection
Idling with warm engine
Pulse generation
(See waveform 4)
A36-24 (#3) - A36-4 (E01)
LG-W - B-L
Injector for direct injection
Idling with warm engine
Pulse generation
(See waveform 4)
A36-25 (#2) - A36-4 (E01)
LG-B - B-L
Injector for direct injection
Idling with warm engine
Pulse generation
(See waveform 4)
A36-28 (VTA2) - A36-29 (E1)
R-Y - Y-B
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
Approximately 1.5 V
Ignition switch ON, Accelerator pedal fully depressed
Approximately 4.3 V
A36-30 (THW) - A36-29 (E1)
BR-W - Y-B
Engine coolant temperature sensor
Idling, Engine coolant temperature 60 to 120°C (176 to 248°F)
0.8 to 1.8 V
A36-31 (IGT3) - A36-4 (E01)
W-G - B-L
Ignition coil (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 13)
A36-32 (#30) - A36-4 (E01)
P-B - B-L
Injector for port injection
Idling with warm engine
Pulse generation
(See waveform 15)
A33-4 (EC) - Body ground
B-L - Body ground
Ground
Always
Below 1 Ω
A33-28 (SLE2) - Body ground
-
Shield
Always
Below 1 Ω
A34-1 (E03) - Body ground
B-R - Body ground
Ground
Always
Below 1 Ω
A34-2 (E04) - Body ground
B-W - Body ground
Ground
Always
Below 1 Ω
A34-3 (E05) - Body ground
W - Body ground
Ground
Always
Below 1 Ω
A34-8 (GND) - Body ground
L-R - Body ground*11
V - Body ground*12
Ground
Always
Below 1 Ω
A34-29 (EKNK) - Body ground
-
Shield
Always
Below 1 Ω
A34-30 (SLE1) - Body ground
GR - Body ground
Shield
Always
Below 1 Ω
A34-35 (SLE3) - Body ground
-
Shield
Always
Below 1 Ω
A35-29 (EPA) - A36-4 (E01)
L - B-L
Ground
Ignition switch ON
0 to 1 V
A35-30 (EPA2) - A36-4 (E01)
Y-B - B-L
Ground
Ignition switch ON
0 to 1 V
A36-3 (E02) - Body ground
B-Y - Body ground
Ground
Always
Below 1 Ω
A36-4 (E01) - Body ground
B-L - Body ground
Ground
Always
Below 1 Ω
A36-29 (E1) - Body ground
Y-B - Body ground
Ground
Ignition switch ON
0 to 1 V
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission
  3. *3: w/ Entry and Start System
  4. *4: w/o Entry and Start System
  5. *5: w/ A/C
  6. *6: w/o A/C
  7. *7: w/ ID Code Box
  8. *8: w/o ID Code Box
  9. *9: w/ EVAP System
  10. *10: except Automatic Air Conditioning System
  11. *11: for RHD
  12. *12: for LHD

WAVEFORM 1
A086155E65
CAN Communication Signal 
ECM Terminal Name
Between CANL and E01
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 2
A086154E73
CAN Communication Signal 
ECM Terminal Name
Between CANH and E01
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 3
A280139E01
Air Fuel Ratio Sensor Heater 
ECM Terminal Name
Between HA1A and E01
Tester Range
5 V/DIV., 50 ms./DIV.
Condition
Idling with cold engine

WAVEFORM 4
A280142E01
Injector for Direct Injection No. 1 (to No. 4) Injection Signal 
ECM Terminal Name
CH1: Between #1 (to #4) and E01
CH2: Between IJF1 or IJF2 and E01
Tester Range
2 V/DIV., 40 μs./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A280144E01
Fuel Pump for High Pressure (Spill Valve) 
ECM Terminal Name
CH1: Between FPD and E01
CH2: Between FPF and E01
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

WAVEFORM 6
A384643E01
Crankshaft Position Sensor and VVT Sensor for Exhaust Camshaft 
ECM Terminal Name
CH1: Between NE+ and NE-
CH2: Between EV1+ and E01
CH3: Between EV2+ and E01
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A384644E01
Crankshaft Position Sensor and VVT Sensor for Intake Camshaft 
ECM Terminal Name
CH1: Between NE+ and NE-
CH2: Between VV1+ and E01
CH3: Between VV2+ and E01
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A280149E02
Engine Speed Signal 
ECM Terminal Name
Between TACH and E01
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Engine speed maintained at 1500 rpm

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 9
A280143E02
Fuel Pump Control 
ECM Terminal Name
Between FPC and E01
Tester Range
5 V/DIV., 5 ms./DIV.
Condition
Ignition switch ON

WAVEFORM 10
A280150E02
Throttle Actuator 
ECM Terminal Name
CH1: Between M+ and E01
CH1: Between M- and E01
Tester Range
CH1: 5 V/DIV., 500 μs./DIV.
CH2: 200 mV/DIV., 500 μs./DIV.
Condition
Idling with warm engine

WAVEFORM 11
A280148E02
Camshaft Timing Oil Control Valve (OCV) 
ECM Terminal Name
Between OC1, OC2, OE1 or OE2 and E01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

WAVEFORM 12
A280147E02
Heated Oxygen Sensor 
ECM Terminal Name
Between HT1B and E01
Tester Range
5 V/DIV., 50 ms./DIV.
Condition
Idling with cold engine

WAVEFORM 13
A280145E02
Ignition Coil (Ignition Signal) 
ECM Terminal Name
Between IGT (1 to 4) and E01
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

WAVEFORM 14
A280141E01
Purge Valve 
ECM Terminal Name
Between PRG and E01
Tester Range
10 V/DIV., 2 s./DIV.
Condition
One of the following conditions is met:
  1. Ignition switch ON
  2. Idling with warm engine, under purge control

WAVEFORM 15
A280146E01
Injector for Port Injection No. 1 (to No. 4) Injection Signal 
ECM Terminal Name
Between # (10 to 40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.