Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (NETWORK GATEWAY ECU)

B311513E04


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  2. Disconnect the A73 and D6 main body ECU (network gateway ECU) connectors.

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No.
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A73-4(GND) - Body ground
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω
    D6-1(GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    3C-4 - Body ground
    None - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    3C-7 - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    3E-1 - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the instrument panel junction block assembly and main body ECU (network gateway ECU) connectors.

  5. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D6-13 (CLTE)* - Body ground
    G - Body ground
    Automatic light control sensor ground
    Always
    Below 1 Ω

    1. *: w/ Automatic Light Control System



  6. Measure the voltage or check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D5-26 (RFOG)*1 - Body ground
    Y - Body ground
    Rear fog light switch signal
    Rear fog light switch on
    Below 1 V
    Rear fog light switch off
    Pulse generation
    (See waveform 2 or 3)
    MB-21 (HU) - Body ground
    None - Body ground
    Dimmer switch high signal
    Dimmer switch in high position
    Below 1 V
    Dimmer switch in low position
    11 to 14 V
    MB-18 (HF) - Body ground
    None - Body ground
    Dimmer switch high flash signal
    Dimmer switch in high flash position
    Below 1 V
    Dimmer switch not in high flash position
    Pulse generation
    (See waveform 2 or 3)
    D6-15 (CLTB)*2 - Body ground
    R - Body ground
    Automatic light control sensor power supply
    Ignition switch ON
    11 to 14 V
    D6-14 (CLTS)*2 - Body ground
    LG - Body ground
    Automatic light control sensor signal
    Ignition switch off
    Below 1 V
    Automatic light control system operates
    Pulse generation
    (See waveform 1)
    D5-24 (FFOG)*3 - Body ground
    W - Body ground
    Front fog light switch signal
    Front fog light switch on
    Below 1 V
    Front fog light switch off
    11 to 14 V
    D5-23 (A)*2 - Body ground
    SB - Body ground
    Light control switch AUTO signal
    Light control switch in AUTO position
    Below 1 V
    Light control switch not in AUTO position
    Pulse generation
    (See waveform 2 or 3)
    D5-2 (HEAD1) - Body ground
    W - Body ground
    Light control switch head signal
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    11 to 14 V
    D5-25 (TAIL) - Body ground)
    BE - Body ground
    Light control switch tail signal
    Light control switch in tail or head position
    Below 1 V
    Light control switch in neither tail nor head position
    11 to 14 V
    MB-30 (FFGO)*3 - Body ground
    None - Body ground
    Front fog relay drive output
    Light control switch in tail and front fog light switch on
    Below 1 V
    Light control switch in tail and front fog light switch off
    11 to 14 V
    A73-2 (HRLY) - Body ground
    L - Body ground
    Headlight relay drive output
    Light control switch in head
    Below 1 V
    Light control switch not in head
    11 to 14 V
    A73-11 (DIM) - Body ground
    G - Body ground
    Dimmer relay drive output
    Dimmer switch in high or high flash position
    Below 1 V
    Dimmer switch in low position
    11 to 14 V

    1. *1: w/ Rear Fog Light
    2. *2: w/ Automatic Light Control System
    3. *3: w/ Front Fog Light

    HINT:
    If the result is not as specified, the main body ECU (network gateway ECU) may have a malfunction.




      B113714E01
    1. Waveform 1
      Item
      Content
      Terminal No. (Symbol)
      D6-14 (CLTS)*1 - Body ground
      Tool setting
      5 V/DIV., 5 ms./DIV.
      Condition
      Ignition switch ON
      Light control switch AUTO
      Automatic light control sensor with a hand → Automatic light control sensor covered exposed to ambient light

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.



    2. B199631E02
    3. Waveform 2
      Item
      Content
      Terminal No. (Symbol)
      D5-26 (RFOG)*2 - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Ignition switch ON
      Rear fog light switch off
      Item
      Content
      Terminal No. (Symbol)
      MB-18 (HF) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Ignition switch ON
      Dimmer switch not in high flash position
      Item
      Content
      Terminal No. (Symbol)
      D5-23 (A)*1 - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Ignition switch ON
      Light control switch not in AUTO position



    4. B199632E04
    5. Waveform 3
      Item
      Content
      Terminal No. (Symbol)
      D5-26 (RFOG)*2 - Body ground
      Tool setting
      5 V/DIV., 60 ms./DIV.
      Condition
      Ignition switch ON
      Rear fog light switch off
      Item
      Content
      Terminal No. (Symbol)
      MB-18 (HF) - Body ground
      Tool setting
      5 V/DIV., 60 ms./DIV.
      Condition
      Ignition switch ON
      Dimmer switch not in high flash position
      Item
      Content
      Terminal No. (Symbol)
      D5-23 (A)*1 - Body ground
      Tool setting
      5 V/DIV., 60 ms./DIV.
      Condition
      Ignition switch ON
      Light control switch not in AUTO position

  1. *1: w/ Automatic Light Control System
  2. *2: w/ Rear Fog Light

HEADLIGHT LEVELING ECU ASSEMBLY

E101528E43


Text in Illustration 
*1
Headlight Leveling ECU Assembly
-
-
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No.
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A16-13(R-DIAG) - Body ground
    V - Body ground
    Headlight drive output
    Always
    Below 1.5 V
    A16-15(L-DIAG) - Body ground
    V-W - Body ground
    Headlight drive output
    Always
    Below 1.5 V