Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Main Body / Data List.

  5. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy light switch signal/ON or OFF
    ON: Driver side door closed
    OFF: Driver side door open
    -
    D-Door Lock Pos SW
    Driver side door unlock detection switch signal/LOCK or UNLOCK
    LOCK: Driver side door locked
    UNLOCK: Driver side door unlocked
    -
    P Door Courtesy SW
    Passenger side door courtesy light switch signal/ON or OFF
    ON: Passenger side door closed
    OFF: Passenger side door open
    -
    P-Door Lock Pos SW
    Passenger side door unlock detection switch signal/LOCK or UNLOCK
    LOCK: Passenger side door locked
    UNLOCK: Passenger side door unlocked
    -
    Luggage Courtesy SW
    Luggage compartment door courtesy switch signal/ON or OFF
    ON: Luggage compartment door open
    OFF: Luggage compartment door closed
    -
    IG SW
    Ignition switch ON signal/ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch off
    -
    ACC SW
    Ignition switch ACC signal/ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch off
    -
    Room Light Output
    Map light assembly output signal/ON or OFF
    ON: Map light assembly on
    OFF: Map light assembly off
    -
    Key Illumination Output
    Ignition key cylinder light output signal/ON or OFF
    ON: Ignition key cylinder light on
    OFF: Ignition key cylinder light off
    -
    D Door Courtesy Light
    Driver courtesy light output signal/ON or OFF
    ON: Driver courtesy light on
    OFF: Driver courtesy light off
    -
    P Door Courtesy Light
    Passenger courtesy light output signal/ON or OFF
    ON: Passenger courtesy light on
    OFF: Passenger courtesy light off
    -
    Lighting Time
    Lighting time of the delay control function (illuminated entry system)/15s, 7.5s or 30s
    15s: 15 seconds
    7.5s: 7.5 seconds
    30s: 30 seconds
    Customized value is displayed
    I/L when ACC OFF
    Function that lights up the interior lights when the ignition switch is turned from on (ACC or IG) to off/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    I/L ON W/Door Key Unlock
    Function that lights up the interior lights when the doors are unlocked/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    Room Light when Aprchd
    Function that lights up the interior lights when a key enters any actuation area/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    Interior Light Control
    Operation of the illuminated entry system/OFF or ON
    OFF: System not operated
    ON: System operated
    Customized value is displayed


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Main Body / Active Test.

  5. Perform the Active Test according to the display on the GTS.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    1. Map light assembly
    2. Engine switch*1
    3. Ignition key cylinder light*2
    ON/OFF
    Map light assembly switch in DOOR position
    Driver Courtesy Lamp
    Driver courtesy light
    ON/OFF
    -
    Passenger Courtesy Lamp
    Passenger courtesy light
    ON/OFF
    -
    Key Ring Light*2
    Ignition key cylinder light
    ON/OFF
    -

    1. *1: w/ Entry and Start System
    2. *2: w/o Entry and Start System