Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Select the following menu items: Powertrain / Cruise Control / Data List.

  5. Read the Data List according to the display on the GTS.

    [Powertrain / Cruise Control / Data List] 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    CCS Mem Vehicle Spd
    Stored vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual stored vehicle speed
    -
    Cruise Request Torque
    Required engine torque / Min.: -32768 Nm, Max.: 32767 Nm
    Actual required engine torque
    -
    Cruise Control
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    CCS Indicator M-CPU
    Cruise control indicator light illumination signal (Main CPU) / ON or OFF
    ON: Cruise control indicator light illuminated in green
    OFF: Cruise control indicator light not on
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    RES/ACC Switch
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Sub CPU) / ON or OFF
    Each time cruise control main switch (ON-OFF button) is pushed, ON/OFF changes
    -
    Main SW M-CPU
    cruise control main switch signal (Main CPU) / ON or OFF
    ON: cruise control main switch (ON-OFF button) pushed
    OFF: cruise control main switch (ON-OFF button) released
    -
    Stop Light Switch 1
    Stop light switch signal1 / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stop Light Switch 2
    Stop light switch signal2 / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Cancel : Main Switch
    "CANCEL CODE" by cruise control main switch operation / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Stop/Brake Switch
    "CANCEL CODE" by brake pedal operation / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Clutch Switch
    "CANCEL CODE" by clutch pedal operation (for Manual Transmission) / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Neutral Switch
    "CANCEL CODE" by shift lever operation (for Automatic Transmission) / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Cancel Switch
    "CANCEL CODE" by CANCEL switch operation / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : IG Switch
    "CANCEL CODE" by ignition switch operation / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Vehicle Speed 1
    "CANCEL CODE" by abnormal vehicle speed signal / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Engine Revolution
    "CANCEL CODE" by raising engine speed / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Out of Range
    "CANCEL CODE" by setting the cruise control outside permitted vehicle speed / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Accel Angle
    "CANCEL CODE" by accelerator pedal operation / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Keeping Vehicle Speed
    "CANCEL CODE" by inability to maintain vehicle speed / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : VSC/TRC Operation
    "CANCEL CODE" by VSC/TRC operation / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : ABS/VSC Abnormal
    "CANCEL CODE" by ABS/VSC abnormality / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Meter Abnormal
    "CANCEL CODE" by combination meter assembly abnormality / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Brake Switch Abnormal
    "CANCEL CODE" by stop light switch assembly abnormality / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Neutral Switch Abnormal
    "CANCEL CODE" by park/neutral position switch abnormality / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Vehicle Speed 2
    "CANCEL CODE" by abnormal vehicle speed change / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Engine Abnormal
    "CANCEL CODE" by engine control system abnormality / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Switch Related to Cruise Control
    "CANCEL CODE" by cruise control main switch abnormality / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Brake Switch Abnormal(Memory)
    "Cruise Cancel : Brake Switch Abnormal" is detected / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Neutral Switch Abnormal(Memory)
    "Cruise Cancel : Neutral Switch Abnormal" is detected / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Vehicle Speed 2(Memory)
    "Cruise Cancel : Vehicle Speed 2" is detected / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Engine Abnormal(Memory)
    "Cruise Cancel : Engine Abnormal" is detected / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : Switch Related to CCS(Memory)
    "Cruise Cancel : Switch Related to CCS" is detected / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Cruise Cancel : ECT Abnormal
    "CANCEL CODE" by automatic transmission system / ON or OFF
    ON: "CANCEL CODE" detected
    OFF: "CANCEL CODE" not detected
    Refer to "CANCEL CODE" (Click here).
    Brake Cancel Switch
    Stop light switch signal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -


PERFORM ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Select the following menu items: Body Electrical / Combination Meter / Active Test.

  5. Perform "Active Test" according to the display on GTS.

    HINT:
    The ignition switch must be turned on to proceed with the Active Test using the GTS.


    [Body Electrical / Combination Meter / Active Test] 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    Cruise control indicator light
    Cruise control indicator light (illuminated in green) ON / OFF
    -
    Indicat. SET
    Cruise control SET indicator light
    Cruise control SET indicator light ON / OFF
    -
    Cruise Warning
    Cruise control indicator light
    Cruise control indicator light (illuminated in amber) ON / OFF
    -