Home › Engine / Hybrid System › FA20 FUEL › FUEL INJECTOR (for Port Injection)

FUEL INJECTOR (for Port Injection) > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
The power window system utilizes a mechanism in which the door glass moves down slightly when the door is opened, and in which the glass moves up when the door closed in order to prevent the door molding from being damaged. When the negative (-) battery terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



3. REMOVE CHAMBER ASSEMBLY
(Click here)


4. REMOVE INJECTOR DRIVER


    A277974E02
  1. Move the lock levers in the direction indicated by the arrow to release the 3 connector locks. Disconnect the 4 connectors from the injector driver.
    Text in Illustration 
    *1
    Lock Lever
    *a
    Release
    V100135
    Lock with Connector
    V100136
    Normal Connector



    A277975
  1. Remove the 3 bolts and injector driver.

    NOTICE:
    Be careful not to drop or strike the injector driver.



5. REMOVE INJECTOR COVER (for Bank 1)


    A279751
  1. Disengage the 4 clamps and separate the wire harness from the injector cover (for bank 1).



  1. for Resin Intake Manifold:



      A277976
    1. Remove the 2 bolts and injector cover (for bank 1).



  1. for Aluminum Intake Manifold:



      A387945
    1. Remove the 2 bolts and disengage the 2 guides, and then remove the injector cover.



6. DISCONNECT NO. 1 FUEL HOSE (for Metal Type)


    A281447
  1. Using SST, disconnect the No. 1 fuel hose from the fuel delivery pipe sub-assembly (Click here).

    SST
    SU003-03936  



7. DISCONNECT NO. 3 FUEL HOSE (for Metal Type)


    A281448
  1. Using SST, disconnect the No. 3 fuel hose from the fuel pipe (Click here).

    SST
    SU003-03936  



8. DISCONNECT NO. 2 FUEL HOSE (for Metal Type)


    A282016
  1. Remove the clamp and disconnect the No. 2 fuel vapor feed hose from the fuel pipe.



9. REMOVE INJECTOR COVER (for Bank 2)


    A281164
  1. Remove the bolt and disconnect the wire harness clamp bracket from the injector cover (for bank 2).



  1. for Resin Intake Manifold:



      A277981
    1. Remove the 2 bolts and injector cover (for bank 2).



  1. for Aluminum Intake Manifold:



      A387943
    1. Remove the 2 bolts and disengage the 2 guides, and then remove the injector cover.



10. DISCONNECT NO. 1 FUEL HOSE (for Clamp Type)


    A279753
  1. Remove the clamp and disconnect the No. 1 fuel hose.

    NOTICE:
    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
    2. Be careful not to splash the fuel.
    3. Receive the fuel remaining inside the fuel hose with a container.
    4. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.



11. SEPARATE FUEL DELIVERY PIPE SUB-ASSEMBLY (for Clamp Type)


    A279754
  1. Remove the bolt and disconnect the fuel delivery pipe sub-assembly.

  1. Disconnect the No. 2 fuel vapor feed hose and move the fuel delivery pipe sub-assembly toward the front of the vehicle.



12. REMOVE FUEL DELIVERY PIPE (for Bank 2)


    A277982
  1. Disconnect the 2 fuel injector assembly connectors.

  1. Disengage the clamp and separate the wire harness.



    A279755
  1. Disconnect the fuel pump assembly connector.



    A277984
  1. Disconnect the No. 2 fuel delivery pipe sub-assembly from the fuel delivery pipe (Click here).



    A277983
  1. Remove the 2 bolts and fuel delivery pipe.

    NOTICE:
    When removing the fuel delivery pipe, hold the pipe by both ends and pull it straight upward.



13. REMOVE FUEL INJECTOR SEAL (for Bank 2)


    A322085
  1. Remove the 2 fuel injector seals.



14. REMOVE FUEL DELIVERY PIPE (for Bank 1)


    A277977
  1. Disconnect the 2 fuel injector assembly connectors.

  1. Disengage the clamp and separate the wire harness.

  1. Disconnect the No. 2 fuel delivery pipe sub-assembly from the fuel delivery pipe (Click here).



    A277978
  1. Remove the 2 bolts and fuel delivery pipe.

    NOTICE:
    When removing the fuel delivery pipe, hold the pipe by both ends and pull it straight upward.



15. REMOVE FUEL INJECTOR SEAL (for Bank 1)


    A321961
  1. Remove the 2 fuel injector seals.



16. REMOVE FUEL INJECTOR ASSEMBLY


    A277979
    A281860E02
  1. Remove the 4 fuel injector assemblies from the fuel delivery pipe.

    NOTICE:
    For reinstallation, attach a tag or label to the injector shaft.



    A321981E01
  1. Remove the fuel injector O-ring and fuel injector grommet from the fuel injector assembly.
    Text in Illustration 
    *1
    Fuel injector O-ring
    *2
    Fuel injector grommet