Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1432/22    Open in Ambient Temperature Sensor Circuit

DTC    B1433/-22    Short in Ambient Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The thermistor assembly is installed in the front part of the condenser to detect the ambient temperature and control the air conditioner. The thermistor assembly is connected to the combination meter assembly and detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The thermistor assembly sends a signal to the air conditioning control assembly via the combination meter assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The combination meter assembly applies a voltage (5 V) to the thermistor assembly and reads voltage changes as changes in the resistance of the thermistor assembly. The combination meter assembly sends the read signal to the air conditioning control assembly via CAN communication.

DTC No.
DTC Detection Condition
Trouble Area
B1432/22
Open in ambient temperature sensor circuit
  1. Ambient temperature sensor (thermistor assembly)
  2. Harness or connector between ambient temperature sensor (thermistor assembly) and air conditioning control assembly
  3. Air conditioning control assembly
B1433/-22
Short in ambient temperature Sensor circuit
  1. Ambient temperature sensor (thermistor assembly)
  2. Harness or connector between ambient temperature sensor (thermistor assembly) and air conditioning control assembly
  3. Air conditioning control assembly

WIRING DIAGRAM


E248911E01


INSPECTION PROCEDURE

NOTICE:
  1. The heater and air conditioning system uses the CAN communication system. First, carry out the check of CAN communication system in accordance with the "HOW TO PROCEED WITH TROUBLESHOOTING", and confirm that there are no problems with the communications system before proceeding with troubleshooting.
  2. Errors with the combination meter assembly may affect this DTC. Prior to carrying out an inspection, inspect "Meter and gauge system" DTCs, and confirm that the combination meter assembly is normal.

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.


Air Conditioner 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Ambient Temp Sensor
(Ambi Temp Sens)
Ambient temperature sensor (thermistor assembly) /
Min: -40.00°C (-40.00°F)
Max: 80.00°C (176.00°F)
Actual ambient temperature displayed
-

OK:
The display is as specified in the normal condition column.

Result:
Result
Proceed to
OK (When troubleshooting according to the DTC)
A
OK (When troubleshooting according to Problem Symptoms Table)
B
NG
C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs

  1. Check the DTCs

    OK:
    DTC is not output.



NG
REPLACE AIR CONDITIONING CONTROL ASSEMBLY
OK

END 

3.INSPECT AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)
  1. Remove the ambient temperature sensor (thermistor assembly) .

  1. Inspect the ambient temperature sensor (thermistor assembly) .



NG
REPLACE AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)
OK


4.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
  1. Disconnect the D7 conditioning meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A48-1 - D7-24(TAM)
    Always
    Below 1 Ω
    A48-2 - D7-25(SG-)
    Always
    Below 1 Ω
    A48-1 - Body ground
    Always
    10 kΩ or higher
    A48-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY